AT29LV256-15JC SL383 Atmel, AT29LV256-15JC SL383 Datasheet
AT29LV256-15JC SL383
Related parts for AT29LV256-15JC SL383
AT29LV256-15JC SL383 Summary of contents
Page 1
... Three-volt-only commands determine the opera- tion of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29LV256 is performed on a sector basis; 64 bytes of data are loaded into the device and then simultaneously programmed. During a reprogram cycle, the address locations and 64 bytes of data are captured at microprocessor speed and internally latched, freeing the address and data bus for other operations ...
Page 2
... Pin Configurations Pin Name A0 - A14 I/ 2.1 PLCC Top View 2.2 TSOP Top View – Type 1 AT29LV256 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect Don’t Connect A11 ...
Page 3
... Device Operation 4.1 Read The AT29LV256 is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual-line control gives designers flexibility in preventing bus contention ...
Page 4
... Once a programming operation has been initiated, and for the duration of t 4.3 Hardware Data Protection Hardware features protect against inadvertent programs to the AT29LV256 in the following ways: (a) V power on delay – once V out 10 ms (typical) before programming; (c) Program inhibit – holding any one of OE low, CE high or WE high inhibits program cycles ...
Page 5
... DATA Polling The AT29LV256 features DATA polling to indicate the end of a program cycle. During a pro- gram cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all out- puts and the next cycle may begin ...
Page 6
... MHz mA 3.6V OUT 1 -100 µ 3. AT29LV256-20 AT29LV256-25 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 3.3V ± 0.3V 3.3V ± 0. OUT High Z High Z ( Manufacturer Code ...
Page 7
... Min Max 150 150 (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact AT29LV256 AT29LV256-20 AT29LV256-25 Min Max Min Max 200 250 200 250 0 100 0 120 ...
Page 8
... Input Test Waveforms and Measurement Level t R 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. These parameters are characterized and not 100% tested. AT29LV256 < Max 6 12 Units Conditions OUT 0563E– ...
Page 9
... Chip Select Hold Time CH t Write Pulse Width ( Data Set-up Time Data, OE Hold Time DH OEH t Write Pulse Width High WPH 15. AC Byte Load Waveforms 15.1 WE Controlled 15.2 CE Controlled 0563E–FLASH–2/07 (1)(2) AT29LV256 Min Max Units 10 ns 100 200 ns 100 200 ns 9 ...
Page 10
... OE must be high when WE and CE are both low through A14 must specify the sector address during each high-to-low transition of WE (or CE) after the software code has been entered. 3. All bytes that are not loaded within the sector being programmed will be indeterminate. AT29LV256 10 Min Max ...
Page 11
... Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 0563E–FLASH–2/07 (1) (1) (1)(3) AT29LV256 Min Typ Max Min Typ ...
Page 12
... The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is BC. 0563E–FLASH–2/07 (1) 24. Software Product Identification (2) (2)( AT29LV256 (1) Exit LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA F0 TO ...
Page 13
... Ordering Code Package AT29LV256-15JC 32J AT29LV256-15TC 28T AT29LV256-15JI 32J AT29LV256-15TI 28T AT29LV256-20JC 32J AT29LV256-20TC 28T AT29LV256-20JI 32J AT29LV256-25JC 32J AT29LV256-25TC 28T AT29LV256-25JI 32J Package Type AT29LV256 Operation Range Commercial (0° to 70° C) Industrial (-40° to 85° C) Commercial (0° to 70° C) Industrial (-40° ...
Page 14
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29LV256 14 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 15
... Orchard Parkway San Jose, CA 95131 R 0563E–FLASH–2/07 PIN SEATING PLANE A1 TITLE 28T, 28-lead (8 x 13.4 mm) Plastic Thin Small Outline Package, Type I (TSOP) AT29LV256 0º ~ 5º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – ...
Page 16
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...