592D686X9010R2T Vishay Sprague, 592D686X9010R2T Datasheet - Page 14

• Manufacturer Part Number: 592D686X9010R2T
• Description: Single Components, Passive Components, Capacitors
• Manufacturer: Vishay Sprague

Notes:
1. A
2. Tape with components shall pass around radius "R" without
Document Number: 40004
Revision: 03-May-05
Double Pitch
Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
TAPE AND REEL PACKAGING in inches [millimeters]
B 0
Tape Size
of the terminals extending from the component body and/or the
body dimensions of the component. The clearance between the
ends of the terminals or body of the component to the sides and
depth of the cavity (A
minimum and 0.020" [0.50 mm] maximum. The clearance
allowed must also prevent rotation of the component within the
cavity of not more than 20 degrees.
damage. The minimum trailer length may require additional
length to provide R minimum for 12 mm embossed tape for reels
with hub diameters approaching N minimum.
12 mm
12 mm
24 mm
8 mm
0
(Top View)
B
For Tape Feeder
Reference only
including draft.
Concentric around B
(Note 5)
0
K
A 0
(Note 6)
B Max.
0
1
are determined by the maximum dimensions to the ends
[0.600]
20˚ Maximum
Component Rotation
0.024
Max.
B
Typical
Component
Cavity
Center Line
Typical
Component
Center Line
(Note 6)
0.004 [0.10]
1
0.179
[4.55]
0.323
0.323
0.791
[20.1]
Max.
[8.2]
[8.2]
T
(Max.)
Max.
0
2
0
K 0
B
Top
Cover
Tape
0
K
0
) must be within 0.002" [0.05 mm]
Deformation
Between
Embossments
Allowable Camber to be 0.039/3.937 [1/100]
Non-Cumulative Over 9.843 [250.0]
D
(Note 5)
1
0.039
0.059
0.059
0.059
[1.0]
[1.5]
[1.5]
[1.5]
Top
Cover
Tape
(Min.)
3.937 [100.0]
0.039 [1.0]
Center Lines
of Cavity
Conformal Coated, Maximum CV
For technical questions, contact: [e-mail]
Solid Tantalum Chip Capacitors
Max.
0.059 + 0.004 - 0.0
0.9843 [250.0]
(T op View)
TANTAMOUNT®, Low Profile,
[1.5 + 0.10 - 0.0]
Camber
0.138 ± 0.002
0.217 ± 0.002
0.217 ± 0.002
0.453 ± 0.04
[11.5 ± 0.03]
USER DIRECTION OF FEED
[3.5 ± 0.05]
[5.5 ± 0.05]
[5.5 ± 0.05]
0.039 [1.0]
Max.
F
A
0
Tape
P 1
B 0
0.157 ± 0.004
[4.0 ± 0.10]
0.157 ± 0.004
0.157 ± 0.004
0.315 ± 0.004
0.472 ± 0.004
DIRECTION OF FEED
[12.0 ± 0.10]
[4.0 ± 0.10]
[4.0 ± 0.10]
[8.0 ± 0.10]
Cathode (-)
P
Anode (+)
1
0.079 ± 0.002
[2.0 ± 0.05]
Maximum
Cavity Size
(Note 1)
Tape and Reel Specifications: All case sizes are available on plastic
embossed tape per EIA-481-1. Tape reeling per IEC 286-3 is also
available. Standard reel diameter is 7" [178 mm]. 13" [330 mm] reels
are available and recommended as the most cost effective packaging
method.
The most efficient packaging quantities are full reel increments on a
given reel diameter. The quantities shown allow for the sealed empty
pockets required to be in conformance with EIA-481-1. Reel size and
packaging orientation must be specified in the Vishay Sprague part
number.
10 Pitches Cumulative
Tolerance on Tape
± 0.008 [0.200]
3. This dimension is the flat area from the edge of the sprocket hole
4. This dimension is the flat area from the edge of the carrier tape
5. The embossment hole location shall be measured from the
6. B
to either the outward deformation of the carrier tape between the
embossed cavities or to the edge of the cavity whichever is less.
opposite the sprocket holes to either the outward deformation of
the carrier tape between the embossed cavity or to the edge of
the cavity whichever is less.
sprocket hole controlling the location of the embossment.
Dimensions of embossment location and hole location shall be
applied independent of each other.
only.
D Min. For Components
0.079 x 0.047 [2.0 x 1.2] and Larger .
(Note 5)
1
0.030 [0.75]
Min. (Note 3)
1
0.030 [0.75]
Min. (Note 4)
R (Min.)
(Note 2)
dimension is a reference dimension for tape feeder clearance
Embossment
0.984
[25.0]
1.181
1.181
[30.0]
1.181
[30.0]
30.0]
F
0.069 ± 0.004
[1.75 ± 0.10]
W
T
2
0.098
0.256
0.256
0.103
[2.5]
[6.5]
[6.5]
[2.6]
(Max.)
(Side or Front Sectional Vie w )
20°
0.315 + .012 - 0.004
[8.0 + 0.3 - 0.1]
Maximum
Component
Rotation
0.472 ± 0.012
0.472 ± 0.012
0.945 ± 0.012
[12.0 ± 0.30]
[12.0 ± 0.30]
[24.0 ± 0.03]
Vishay Sprague
W
www.vishay.com
592D
(Note 1)
A
0
B
0
K
0
14