RN42-I/RM Roving Networks, RN42-I/RM Datasheet
RN42-I/RM
Specifications of RN42-I/RM
Available stocks
Related parts for RN42-I/RM
RN42-I/RM Summary of contents
Page 1
... Computer accessories Description The RN- small form factor, low power, class 2 Bluetooth radio for designer’s who want to add wireless capability to their products. The RN-42 supports multiple interface protocols, is simple to design in, and is fully certified, making it a complete embedded Bluetooth solution. The RN-42 is functionally compatible with the RN 41 ...
Page 2
OVERVIEW • Baud rate speeds: 1,200 bps up to 921 Kbps, non-standard baud rates can be programmed • Class 2 radio, 60 feet (20 meters) distance, 4 dBm output transmitter, -80 dBm typical receive sensitivity Frequency 2,402 ~ 2,480 MHz ...
Page 3
... After Two Walls After Three Walls The readings shown in Table 6 are approximate and may vary depending upon the RF environment. Bluetooth hops in a pseudo-random fashion over the 79 frequencies in the ISM band to adapt to the interference. Data throughput and range vary depending on the RF interference environment. ...
Page 4
Figure 2. RN-42/RN-42-N Pinout GND 1 RN-42 SPI_MOSI 2 Top View GPIO6 3 GPIO7 4 RESET 5 SPI_CLOCK 6 PCM_CLK 7 PCM_SYNC 8 PCM_IN 9 PCM_OUT 10 VDD 11 GND Table ...
Page 5
... Figure 3 shows the module’s physical dimensions. Figure 3. RN-42/RN-42-N Physical Dimensions All Dimensions Are In mm www.rovingnetworks.com Description Output from RN-42 Input to RN-42 with weak pulldown Output from RN42 Input to RN-42 with weak pulldown No Connect No Connect Not Used Output from RN-42 Input to RN-42 with weak pulldown Input to RN-42 with weak pulldown ...
Page 6
TYPICAL APPLICATION SCHEMATIC Figure 4 shows a typical application schematic. Because the RN-41 and RN-42 are functionally compatible, this diagram applies to both modules. Figure 4. Application Schematic www.rovingnetworks.com Version 2.31r 10/15/2012 RN -42 -DS 6 ...
Page 7
... MCP809, MCP102/121, and Torex XC61F. Factory Reset Using GPIO4 Roving Networks recommends that designers connect the GPIO4 pin to a switch, jumper, or resistor so it can be accessed. This pin can be used to reset the module to its factory default settings, which is critical in situations where the module has been misconfigured ...
Page 8
... Using the module in HCI mode allows designers to implement profiles that are not natively supported on the Bluetooth module. NOTE: HCI mode requires a separate firmware build that must be loaded into the module’s flash at the factory. Is not upgradeable in the field. Roving Networks offers HCI mode in two hardware interfaces: HCI over UART • HCI over USB • ...
Page 9
... Because the RN-42-N does not contain an antenna, it does not carry regulatory approvals. If designers use Roving Networks recommended design, they can file for a permissible antenna change and use Roving Networks’ regulatory approvals. The recommended antenna design for the RN- PCB trace antenna. To meet the regulatory compliance information, customers must use the trace pattern shown in Figure 6 ...
Page 10
Antenna Design The pattern from the RF_OUT terminal pad should be designed with 50 ohms impedance and traced with straight lines (see Figure 7). The RF_OUT signal line should not run under or near the RN-21 module. The GND plane ...
Page 11
... FCC CRF Title 47 Part 15 Subpart C T9J-RN42 ETSI EN 301 489-1 V1.8.1 ETSI EN 301 489-17 V2.1.1 ETSI EN 300 328 V1.7.1 IC RSS-210 low power comm. device 6514A-RN42 FCC CFR47 Part 15 subclass B EN 55022 Class B radiated EN61000-4-2 ESD immunity EN61000-4-3 radiated field EN61000-4-6 RF immunity EN61000-4-8 power magnetic immunity ...
Page 12
... Roving Networks products are not authorized for use in safety-critical applications (such as life support) where a failure of the Roving Networks product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. ...