581G-02ILFT IDT, 581G-02ILFT Datasheet
581G-02ILFT
Specifications of 581G-02ILFT
Related parts for 581G-02ILFT
581G-02ILFT Summary of contents
Page 1
... INB SELA FBIN S1:0 ICS581-02 DIV INA INB FBIN 2 S1:0 IDT™ / ICS™ ZERO DELAY GLITCH-FREE CLOCK MULTIPLEXER Features • 16-pin TSSOP package • RoHS compliant packaging • No short pulses or glitches on output • Operates from 6 to 200 MHz • Low skew outputs • ...
Page 2
... OE1 OE0 ICS581-01/02 Note: Z indicates that the output high impedance state IDT™ / ICS™ ZERO DELAY GLITCH-FREE CLOCK MULTIPLEXER 16 SELA 15 VDD 14 CLK1 13 CLK2 12 CLK3 11 CLK4 10 GND 9 OE1 Timeout Selection DIV 0 1 ICS581-02 only ...
Page 3
... If output termination resistors are used, the feedback should be connected before the resistor property of the PLL used on this chip that it will align rising edges on FBIN and IDT™ / ICS™ ZERO DELAY GLITCH-FREE CLOCK MULTIPLEXER Pin Type Input Select 0 for frequency range ...
Page 4
... If the two input frequencies require different input ranges (see table on page two), then the highest range should be permanently selected. When the selected input clock is outside this range, jitter and input skew specifications may not be met. Consult IDT for more information. VDD S0 ...
Page 5
... Stresses above the ratings listed below can cause permanent damage to the ICS581-01/02. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. ...
Page 6
... Note 3: Time taken for output to lock to new clock when mux selection changed from INA to INB. Note 4. With 50 MHz on INA and 150 MHz on INB. Note 5: With 100 MHz on both INA and INB, 180 out of phase. IDT™ / ICS™ ZERO DELAY GLITCH-FREE CLOCK MULTIPLEXER Conditions C ...
Page 7
... Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case Marking Diagram (Pb-Free) ICS 581GxxxLF YYWW$$ Notes: 1. xxx is either 01, 01I, 02, or 02I. 2. YYWW is the last two digits of the year and the week number that the part was assembled. 3. Bottom marking: country of origin if not USA. ...
Page 8
... Package Outline and Package Dimensions Package dimensions are kept current with JEDEC Publication No. 95, MO-153 IDT™ / ICS™ ZERO DELAY GLITCH-FREE CLOCK MULTIPLEXER (16-pin TSSOP, 4.40 mm Body, 0.65 mm Pitch) Symbol ...
Page 9
... See page 7 581G-02ILF 581G-02ILFT 581G-02LF 581G-02LFT "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use ...
Page 10
... Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners ...