MAX5386MEVMINIQU+ Maxim Integrated, MAX5386MEVMINIQU+ Datasheet
MAX5386MEVMINIQU+
Specifications of MAX5386MEVMINIQU+
Related parts for MAX5386MEVMINIQU+
MAX5386MEVMINIQU+ Summary of contents
Page 1
... The MAX5386M IC features dual volatile 50kI 256-tap, potentiometers and communi- cates through an SPIK-compatible serial interface. The MAX5386MEVMINIQU+ evaluation system (EV sys- tem) includes the EV kit and the MINIQUSB+ interface board. The MINIQUSB+ interface board can be used to enable PC communication through the 3-wire serial inter- face ...
Page 2
... TSSOP) Not installed, digital U4 0 potentiometer (10 FMAX *EP = Exposed pad. µMAX is a registered trademark of Maxim Integrated Products, Inc. SUPPLIER Murata Electronics North America, Inc. TDK Corp. Note: Indicate that you are using the MAX5386_, MAX5388, MAX5391, or MAX5393 when contacting these component suppliers. ...
Page 3
Windows Start_ |_ Programs menu. 3) Verify that shunts are correctly installed on the jumpers listed in Table 1 for proper operation of the EV kit. 4) Connect the multimeters across the MAX5386M’s (U1) WA and ...
Page 4
MAX5386M Evaluation System Figure 1. MAX5386M Evaluation Kit Software Main Window 4_ _ _______________________________________________________________________________________ ...
Page 5
The MAX5386M EV kit is now ready for additional testing. See the Detailed Description of Software section for more information on the software features. Detailed Description of Software Graphical User Interface (GUI) Panel The MAX5386M EV kit software GUI ...
Page 6
MAX5386M Evaluation System Pressing the Default button resets potentiometer A and B wiper positions in the MAX5386M to the factory-default midscale position. The Status indicator in the Interface group box displays EV_ Kit_ Operational when the EV kit enters the ...
Page 7
Figure 3. Simple Low-Level 3-Wire Interface General Troubleshooting Problem:_Software_reports_it_cannot_find_the_interface_ circuit: • Is the USB cable connected to the MINIQUSB+ board? • Has Windows plug-and-play detected the board? Bring up Control_ Panel->System->Device_ Manager, and look at what device nodes are indicated ...
Page 8
MAX5386M Evaluation System EV Kit VDD Input Source The VPOWER rail is typically supplied as 3. the MINIQUSB+ interface board circuitry, or 2.6V using LDO regulator U6. LDO regulator U5 output is set to 1.7V and is ...
Page 9
Potentiometer, Voltage-Divider, or Variable Resistor with Ground Reference The EV kit provides an option to configure the MAX5386M as a potentiometer or voltage-divider, open end, or with ground reference, respectively. Use jumpers JU3 and JU4 for potentiometer A, and jumpers ...
Page 10
MAX5386M Evaluation System Table_9._Jumper_Configuration_(JU1–JU20) JUMPER SHUNT_POSITION Installed JU1 Not installed* 1-2 JU2 2-3* Not installed Not installed JU3 Installed* Not installed JU4 Installed* Not installed JU5 Installed* Not installed JU6 Installed* 1-2* JU7 2-3 Not installed JU8 Installed* Not installed ...
Page 11
Figure 4. MAX5386M EV Kit Schematic _______________________________________________________________________________________ _ 11 MAX5386M Evaluation System ...
Page 12
MAX5386M Evaluation System Figure 5. MAX5386M EV Kit Component Placement Guide—Component Side 12_ _ ______________________________________________________________________________________ 1.0’’ ...
Page 13
Figure 6. MAX5386M EV Kit PCB Layout—Component Side _______________________________________________________________________________________ _ 13 MAX5386M Evaluation System 1.0’’ ...
Page 14
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ____________________ ________ Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 14_ 2010 Maxim Integrated Products © ...