MAX199AEAI-T Maxim Integrated, MAX199AEAI-T Datasheet - Page 10

• Manufacturer Part Number: MAX199AEAI-T
• Description: Analog to Digital Converters - ADC
• Manufacturer: Maxim Integrated

Specifications of MAX199AEAI-T

• Number Of Channels: 8
• Architecture: SAR
• Conversion Rate: 100 KSPs
• Resolution: 12 bit
• Input Type: Single-Ended
• Snr: Yes
• Interface Type: Parallel
• Operating Supply Voltage: 4.75 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SSOP-28
• Maximum Power Dissipation: 762 mW
• Minimum Operating Temperature: - 40 C
• Number Of Converters: 1
• Voltage Reference: 4.096 V

Conversions are initiated with a write operation, which
selects the mux channel and configures the MAX199 for
either unipolar or bipolar input range. A write pulse (WR
+ CS) can either start an acquisition interval or initiate a
combined acquisition plus conversion. The sampling
interval occurs at the end of the acquisition interval.
The ACQMOD bit in the input control byte offers two
options for acquiring the signal: internal or external.
The conversion period lasts for 12 clock cycles in either
internal or external clock or acquisition mode.
Multi-Range (±4V, ±2V, +4V, +2V),
+5V Supply, 12-Bit DAS with 8+4 Bus Interface
Table 5. Data-Bus Output
Figure 5. Conversion Timing Using Internal Acquisition Mode
10
PIN
D0
D1
D2
D3
D4
D5
D6
D7
______________________________________________________________________________________
CS
WR
D7–D0
RD
HBEN
INT
DOUT
HBEN = LOW
B0 (LSB)
t
CSWS
B1
B2
B3
B4
B5
B6
B7
How to Start a Conversion
HIGH-Z
t
DS
B8
B9
B10
B11 (MSB)
B11 (BIP = 1) / 0 (BIP = 0)
B11 (BIP = 1) / 0 (BIP = 0)
B11 (BIP = 1) / 0 (BIP = 0)
B11 (BIP = 1) / 0 (BIP = 0)
t
WR
t
CS
ACQMOD ="0"
CONTROL
BYTE
HBEN = HIGH
t
ACQI
t
t
DH
CSWH
t
CONV
t
D0
t
Writing a new control byte during the conversion cycle
will abort the conversion in progress and start a new
acquisition interval.
Select internal acquisition by writing the control byte
with the ACQMOD bit cleared (ACQMOD = 0). This
causes the write pulse to initiate an acquisition interval
whose duration is internally timed. Conversion starts
when this six-clock-cycle acquisition interval (3µs with
f
Use the external acquisition timing mode for precise con-
trol of the sampling aperture and/or independent control of
acquisition and conversion times. The user controls acqui-
sition and start-of-conversion with two separate write puls-
es. The first pulse, written with ACQMOD = 1, starts an
acquisition interval of indeterminate length. The second
write pulse, written with ACQMOD = 0, terminates acquisi-
tion and starts conversion on WR’s rising edge (Figure 6).
However, if the second control byte contains ACQMOD =
1, an indefinite acquisition interval is restarted.
The address bits for the input mux must have the same
values on the first and second write pulses. Power-
down mode bits (PD0, PD1) can assume new values on
the second write pulse (see Power-Down Mode ).
CSRS
CLK
= 2MHz) ends. See Figure 5.
t
INT1
HIGH / LOW
BYTE VALID
t
D01
HIGH / LOW
BYTE VALID
External Acquisition
Internal Acquisition
t
t
CSRH
TR
HIGH-Z