SPC5646CCF0MLU1 Freescale Semiconductor, SPC5646CCF0MLU1 Datasheet - Page 58

• Manufacturer Part Number: SPC5646CCF0MLU1
• Description: 32-bit Microcontrollers - MCU 3M FLASH,25 6K RAM,CSE
• Manufacturer: Freescale Semiconductor

Specifications of SPC5646CCF0MLU1

• Rohs: yes
• Core: e200
• Processor Series: MPC5646C
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 120 MHz
• Program Memory Size: 3 MB
• Data Ram Size: 256 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 0.3 V to 6.2 V
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: LQFP-176
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit, 12 bit
• A/d Channels Available: 33
• Interface Type: CAN, I2C, SCI, SPI
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 147
• Number Of Timers: 32
• Program Memory Type: Flash
• Supply Voltage - Max: 6.2 V
• Supply Voltage - Min: 0.3 V

Electrical Characteristics
58
1
2
3
4
5
6
7
8
Adders in LP
(96 KB RAM
(64 KB RAM
(8 KB RAM
I
I
I
DDSTDBY3
retained)
DDSTDBY2
retained)
DDSTDBY1
retained)
Except for I
V
ambient temperature.
Target typical current consumption for the following typical operating conditions and configuration. Process = typical,
Voltage = 1.2 V.
Target maximum current consumption for mode observed under typical operating conditions. Process = Fast, Voltage
= 1.32 V.
Running consumption is given on voltage regulator supply (V
toggling. This value is highly dependent on the application. The given value is thought to be a worst case value with
all cores and peripherals running, and code fetched from code flash while modify operation on-going on data flash. It
is to be noticed that this value can be significantly reduced by application: switch-off not used peripherals (default),
reduce peripheral frequency through internal prescaler, fetch from RAM most used functions, use low power mode
when possible.
Higher current may sunk by device during power-up and standby exit. Please refer to in rush current in
Maximum “allowed” current is package dependent.
Only for the “P” classification: Code fetched from RAM: Serial IPs CAN and LIN in loop back mode, DSPI as Master,
PLL as system Clock (4 x Multiplier) peripherals on (eMIOS/CTU/ADC) and running at max frequency, periodic
SW/WDG timer reset enabled. RUN current measured with typical application with accesses on both code flash and
RAM.
I
I
I
I
DDMAX
DDSTOP
DDHALT
DDRUN
mode
DD
Symbol
= 3.3 V ± 10% / 5.0 V ± 10%, T
5
DDMAX
CC D RUN mode maximum
CC P RUN mode typical average
CC P HALT mode current
CC P STOP mode current
CC P STANDBY3 mode
CC C STANDBY2 mode
CC C STANDBY1 mode
CC T 32 KHz OSC
C
D
P
C
C
C
C
C
and I
Table 24. Low voltage power domain electrical characteristics
average current
current
current
current
current
4–40 MHz OSC
16 MHz IRC
128 KHz IRC
DDRUN
8
13
14
15
Parameter
, all the current values are total current drawn from V
MPC5646C Microcontroller DataSheet, Rev. 5.1
A
= 40 to 125 °C, unless otherwise specified All temperatures are based on an
11
12
No clocks active T
No clocks active T
No clocks active T
No clocks active T
at 120 MHz
at 120 MHz
at 80 MHz
—
—
—
—
—
Conditions
DDREG
—
T
T
T
T
T
T
T
T
T
T
T
T
T
). It does not include consumption linked to I/Os
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
= 25 °C
= 25 °C
= 125 °C
= 25 °C
= 125 °C
= 25 °C
= 125 °C
= 25 °C
= 125 °C
= 25 °C
= 125 °C
= 25 °C
= 125 °C
= 25 °C
= 25 °C
= 25 °C
= 25 °C
2
DD_HV_A
Min
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
and V
1
Typ
110
Value
210
150
180
400
630
500
230
20
35
16
50
40
25
—
—
—
—
8
3
DD_HV_B
300
150
Max
1200
1200
200
1100
270
650
500
Table
27
80
60
75
70
65
5
3
5
6,7
10
.
9
4
22.
Freescale
Unit
mA
mA
mA
mA
mA
mA
mA
mA
µA
µA
µA
µA
µA
µA
µA
µA
µA
µA