SIT9001AC-43-25E2-14.74560Y SiTime, SIT9001AC-43-25E2-14.74560Y Datasheet
SIT9001AC-43-25E2-14.74560Y
Specifications of SIT9001AC-43-25E2-14.74560Y
Related parts for SIT9001AC-43-25E2-14.74560Y
SIT9001AC-43-25E2-14.74560Y Summary of contents
Page 1
... Frequency stability • ±50 ppm or ±100 ppm (Spread = OFF) • Operating voltage • 1.8V or 2.5 or 3.3 V • Other voltages up to 3.63 V (contact SiTime) • Operating Temperature Range • Industrial, -40°C to +85°C • Extended Commercial, -20°C to +70°C • World’s Smallest footprints: • ...
Page 2
... Power down (either output enable or standby) mode options are available for both down spread and center spread versions of the SiT9001. The SiT9001, by eliminating the quartz crystal, has improved immunity, shock, strain and humidity. programmable To order samples www.sitime.com and click on Request Sample” link. Page ±0.50% ± ...
Page 3
... Min. Typ. 2.97 3.3 2.25 2.5 1.7 1.8 -50 – -100 – -20 – -40 – – – Page Max. Unit 150 °C +3.66 V 2000 V 75 °C/W 24 °C/W 260 ° 1,000+ years Max. Unit 3.63 V 2.75 V 1.9 V +50 ppm +100 ppm 70 °C 85 ° www.sitime.com ...
Page 4
... Typ. Max. Unit – – %Vdd – 10 %Vdd – – %Vdd – 30 %Vdd – – – Typ. Max. Unit – – %Vdd – 10 %Vdd – – %Vdd – 30 %Vdd – – – www.sitime.com ...
Page 5
... Page Typ. Max. Unit – 200 MHz – 1.0 1.5 ns 1.0 1 Typ. Max. Unit – 200 MHz – 1.0 1.5 ns 1.0 1 Typ. Max. Unit – 200 MHz – 1.0 1.5 ns 1.0 1 www.sitime.com ...
Page 6
... SiT9001 High Performance Spread Spectrum Oscillator Ordering Information SiT9001AC - Part Family “SiT9001” Revision Letter “A” is the revision of Silicon Temperature Range “C” Extended Commercial, -20 to 70C “I” Industrial, -40 to 85C Output Drive Strength “-“ = Default drive Package Size “ ...
Page 7
... The value of “Y” depend on the assembly location of the device capacitor of value 0.1μF between VDD and GND is recommended. Rev. 1.07 Land Pattern (recommended) (mm) 2.1 0.9 2.39 1.15 Do not Connect the center pad or Connect it to Device’s GND Page [4] 2.2 1.4 2.54 1.5 www.sitime.com ...
Page 8
... SiTime Corporation 2010. The information contained herein is subject to change at any time without notice. SiTime assumes no responsibility or liability for any loss, damage or defect of a Product which is caused in whole or in part by (i) use of any circuitry other than circuitry embodied in a SiTime product, (ii) misuse or abuse including static discharge, neglect or accident, (iii) unauthorized modification or repairs which have been soldered or altered during assembly and are not capable of being tested by SiTime under its normal test conditions, or (iv) improper installation, storage, handling, warehousing or transportation, or (v) being subjected to unusual physical, thermal, or electrical stress ...