MAX1158BEUP-T Maxim Integrated, MAX1158BEUP-T Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
MAX1158BEUP-T
Manufacturer Part Number
MAX1158BEUP-T
Description
Analog to Digital Converters - ADC
Manufacturer
Maxim Integrated
Datasheet
1.MAX1156AEUP-T.pdf
(15 pages)
Specifications of MAX1158BEUP-T
Number Of Channels
1
Architecture
SAR
Conversion Rate
135 KSPs
Resolution
14 bit
Input Type
Single-Ended
Snr
85 dB
Interface Type
Parallel
Operating Supply Voltage
5 V
Maximum Operating Temperature
+ 85 C
Package / Case
TSSOP-20
Maximum Power Dissipation
879 mW
Minimum Operating Temperature
- 40 C
Number Of Converters
1
Voltage Reference
Internal, External
An external reference can be placed at either the input
(REFADJ) or the output (REF) of the MAX1156/
MAX1158/MAX1174’s internal buffer amplifier. Using
the buffered REFADJ input makes buffering the exter-
nal reference unnecessary. The input impedance of
REFADJ is typically 5kΩ. The internal buffer output
must be bypassed at REF with a 10µF capacitor.
Connect REFADJ to AV
Directly drive REF using an external 3.8V to 4.2V refer-
ence. During conversion, the external reference must
be able to drive 100µA of DC load current and have an
output impedance of 10Ω or less.
For optimal performance, buffer the reference through
an op amp and bypass REF with a 10µF capacitor.
Consider the MAX1156/MAX1158/MAX1174’s equiva-
lent input noise (0.32LSB) when choosing a reference.
EOC is provided to flag the microprocessor when a
conversion is complete. The falling edge of EOC sig-
nals that the data is valid and ready to be output to the
bus. D0–D13 are the parallel outputs of the
MAX1156/MAX1158/MAX1174. These three-state out-
puts allow for direct connection to a microcontroller I/O
bus. The outputs remain high-impedance during acqui-
sition and conversion. Data is loaded onto the output
bus with the third falling edge of CS with R/C high (after
t
high impedance. The MAX1156/MAX1158/MAX1174
then wait for the next falling edge of CS to start the next
conversion cycle (see Figure 2).
14-Bit, 135ksps, Single-Supply ADCs with
Bipolar Analog Input Range
Figure 5. Selecting Standby Mode
10
DO
REF AND
BUFFER
POWER
). Bringing CS high forces the output bus back to
EOC
______________________________________________________________________________________
R/C
CS
ACQUISITION
Reading the Conversion Result
DD
to disable the internal buffer.
CONVERSION
External Reference
DATA
OUT
HBEN toggles the output between the high/low byte.
The low byte is loaded onto the output bus when HBEN
is low and the high byte is on the bus when HBEN is
high. The two MSBs of the high byte are always zero.
Figures 8, 9, and 10 show the MAX1156/MAX1158/
MAX1174 output transfer functions. The MAX1158 and
MAX1174 outputs are coded in offset binary, while the
MAX1156 is coded in standard binary.
Most applications require an input buffer amplifier to
achieve 14-bit accuracy and prevent loading the
source. Switch the channels immediately after acquisi-
tion, rather than near the end of or after a conversion,
when the input signal is multiplexed. This allows more
time for the input buffer amplifier to respond to a large
step-change in input signal. The input amplifier must
have a high enough slew rate to complete the required
output voltage change before the beginning of the
acquisition time. Figure 11 shows an example of this
circuit using the MAX427.
Figures 12a and 12b show how the MAX1158 and
MAX1174 analog input current varies depending on
whether the chip is operating or powered down. The
part is fully powered down between conversions if the
voltage at R/C is set high during the second falling
edge of CS. The input current abruptly steps to the
powered up value at the start of acquisition. This step
in the input current can disrupt the ADC input, depend-
ing on the driving circuit’s output impedance at high
frequencies. If the driving circuit cannot fully settle by
Figure 6. Selecting Shutdown Mode
REF AND
BUFFER
POWER
EOC
R/C
CS
ACQUISITION
CONVERSION
Transfer Function
Input Buffer
DATA
OUT