RS9110-N-11-24-02 Redpine Signals, RS9110-N-11-24-02 Datasheet - Page 25
![no-image](/images/no-image-200.jpg)
RS9110-N-11-24-02
Manufacturer Part Number
RS9110-N-11-24-02
Description
WiFi / 802.11 Modules Single band
Manufacturer
Redpine Signals
Datasheet
1.RS9110-N-11-24.pdf
(28 pages)
Specifications of RS9110-N-11-24-02
Rohs
yes
Protocol Supported
802.11 b/g
Frequency Band
2.4 GHz
Data Rate
1 Mbps to 54 Mbps
Interface Type
SPI
Transmit Power (max)
17 dBm
Antenna Connector Type
Chip
Operating Supply Voltage
3.3 V
Maximum Operating Temperature
+ 85 C
Dimensions
13.7 mm x 12.9 mm
Minimum Operating Temperature
- 40 C
Modulation Technique
CCK, DSSS, OFDM
Security
WEP 64/128 bit AES, WPA2
7.2.3: Host Abstraction Layer (HAL)
7.2.4: Wireless Control Block (WCB)
7.2.4.1: TCP/IP Control frames
7.2.5: Station Management Entity (SME)
7.2.6: WPA Supplicant
7.2.7: Power Save Modes
Redpine Signals, Inc.
7.2.7.1: Power mode 0
7.2.7.2: Power mode 1
R
R
from 9600 to 3686400 bps. There is support for AT commands to configure
and operate the module through UART interface.
The HAL abstracts the lower layers in the host interface with which the
RS9110-N-11-24 module is connected. The HAL interacts with the Wireless
Control Block layer for the processing of the frames obtained from or destined
to the Host.
The data from/to the Host is classified as Wi-Fi specific frames and TCP/IP
specific frames. The WCB layer processes the frame obtained and acts
accordingly. The functionality of the WCB module depends on the type of the
frame and the direction of the frame (in case of TCP/IP) as described below.
If the frames from the host are interpreted as TCP/IP specific frames then the
WCB interacts with the TCP/IP stack.
The SME is the core layer, which manages the Wi-Fi connectivity. The SME
maintains the state machine to detect the activity on the Wi-Fi network and
indicates to the user accordingly. It also performs re-association to the
configured access point in Infrastructure mode. It interacts with the WPA
supplicant if Security is enabled in the Wi-Fi network.
The WPA supplicant is used to initiate the 802.1x/EAP authentication if WPA2-
PSK is used as the security parameter. It also plays a major part in
performing the 4-way handshake to derive the PTK in WPA2-PSK modes.
The RS9110-N-11-2X module supports three power modes. The Host can
switch among the power modes depending on the Wi-Fi connection status as
defined in this section.
In this mode, power save is disabled in the RS9110-N-11-2X module. The
module will be in Power Mode 0 by default.
The RS9110-N-11-2X module powers off the Baseband, RF and also the Core
Control block in this mode. To power off the Core Control block, the RS9110-
N-11-2X module sends request to Host for permission to sleep.
Once the permission is received the Core Control block is powered off. The
Host has to wait for the module to wakeup based on the timer that is
configured by the Host, before it can transmit any packets.
The functioning of the module in this mode depends on the connection status
as explained below
S
S
-
-
9
9
1
1
1
1
0
0
M
M
-
-
N
N
o
o
-
-
d
d
1
1
u
u
1
1
l
l
-
-
e
e
2
2
w
w
4
4
i
i
V
V
S
S
t
t
D
D
h
h
e
e
e
e
a
a
r
r
l
l
N
N
t
t
s
f
f
s
a
a
i
i
C
e
e
C
o
o
s
s
t
t
o
o
h
h
n
n
w
w
n
n
e
e
2
2
o
t
o
t
e
e
a
a
.
.
r
r
t
t
2
2
i
k
i
k
n
n
i
i
n
e
e
n
d
g
d
g
8
8
S
S
0
0
t
t
a
a
2
2
c
c
.
.
k
k
1
1
1
1
b
b
/
/
g
g
/
/
n
n
Page 25