CAT25256ZD2I-GT2 ON Semiconductor, CAT25256ZD2I-GT2 Datasheet - Page 2

• Manufacturer Part Number: CAT25256ZD2I-GT2
• Description: EEPROM 256KB SPI SER CMOS EEPROM
• Manufacturer: ON Semiconductor

Specifications of CAT25256ZD2I-GT2

• Rohs: yes
• Memory Size: 256 Kbit
• Organization: 32 x 8
• Data Retention: 100 yr
• Maximum Clock Frequency: 1000 KHz
• Maximum Operating Current: 2 mA
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: TDFN-8
• Interface Type: SPI
• Minimum Operating Temperature: - 40 C

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The DC input voltage on any pin should not be lower than −0.5 V or higher than V
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
3. Page Mode, V
4. The new product revision (E) uses ECC (Error Correction Code) logic with 6 ECC bits to correct one bit error in 4 data bytes. Therefore, when
Table 1. ABSOLUTE MAXIMUM RATINGS
Table 2. RELIABILITY CHARACTERISTICS
Table 3. D.C. OPERATING CHARACTERISTICS − MATURE PRODUCT
(
V
Operating Temperature
Storage Temperature
Voltage on any Pin with Respect to Ground (Note 1)
Symbol
N
undershoot to no less than −1.5 V or overshoot to no more than V
and JEDEC test methods.
a single byte has to be written, 4 bytes (including the ECC bits) are re−programmed. It is recommended to write by multiple of 4 bytes in order
to benefit from the maximum number of write cycles.
CC
V
V
I
V
V
I
END
I
I
CCW
CCR
V
I
V
SB1
SB2
OH1
OH2
OL1
OL2
I
LO
L
IH
IL
Symbol
= 1.8 V to 5.5 V, T
(Note 3, 4)
T
DR
Supply Current
(Read Mode)
Supply Current
(Write Mode)
Standby Current
Standby Current
Input Leakage Current
Output Leakage
Current
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Output High Voltage
CC
Parameter
= 5 V, 25°C.
Endurance
Data Retention
A
= −40°C to +85°C and V
Read, V
SO open
Write, V
SO open
V
WP = V
V
V
WP = GND, HOLD = GND,
V
V
CS = V
V
V
V
V
V
IN
CC
IN
CC
IN
OUT
CC
CC
CC
CC
= GND or V
= GND or V
= GND or V
Parameters
= 5.5 V
= 5.5 V
> 2.5 V, I
> 2.5 V, I
> 1.8 V, I
> 1.8 V, I
Parameter
= GND or V
CC
CC
CC
CC
,
, HOLD = V
CC
= 5.5 V,
= 5.5 V,
(Note 2)
OL
OH
OL
OH
= 2.5 V to 5.5 V, T
CC
CC
CC
= 3.0 mA
= 150 mA
= −1.6 mA
= −100 mA
CC
, CS = V
, CS = V
http://onsemi.com
Test Conditions
CC
,
CC
CC
CC
2
,
,
A
+ 1.5 V, for periods of less than 20 ns.
= −40°C to +125°C, unless otherwise specified.)
10 MHz / −40°C to 85°C
5 MHz / −40°C to 125°C
10 MHz / −40°C to 85°C
5 MHz / −40°C to 125°C
T
T
T
T
T
T
A
A
A
A
A
A
= −40°C to +85°C
= −40°C to +125°C
= −40°C to +85°C
= −40°C to +125°C
= −40°C to +85°C
= −40°C to +125°C
CC
+ 0.5 V. During transitions, the voltage on any pin may
1,000,000
Min
100
V
V
CC
CC
0.7 V
−0.5
Min
−2
−1
−1
− 0.8 V
− 0.2 V
Program / Erase Cycles
−45 to +130
−65 to +150
−0.5 to +6.5
CC
Ratings
Units
Years
V
0.3 V
CC
Max
0.4
0.2
2
2
4
4
1
3
4
5
2
1
2
+ 0.5
CC
Units
Units
°C
°C
V
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
mA
V
V
V
V
V
V