CAT24C128YIGT3JN ON Semiconductor, CAT24C128YIGT3JN Datasheet
CAT24C128YIGT3JN
Specifications of CAT24C128YIGT3JN
Related parts for CAT24C128YIGT3JN
CAT24C128YIGT3JN Summary of contents
Page 1
... Figure 1. Functional Symbol *Available for New Product (Rev For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2012 October, 2012 − Rev PDIP−8 ...
Page 2
Table 1. ABSOLUTE MAXIMUM RATINGS Storage Temperature Voltage on Any Pin with Respect to Ground (Note 1) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not ...
Page 3
Table 5. D.C. OPERATING CHARACTERISTICS − New Product (Rev 1 5 −40°C to +85°C and Symbol Parameter I Read Current Read, f CCR I Write Current CCW I Standby ...
Page 4
Table 7. A.C. CHARACTERISTICS ( −40°C to +85°C and Symbol Parameter F Clock Frequency SCL t START Condition Hold Time HD:STA t Low Period of SCL Clock LOW t ...
Page 5
... SCL: The Serial Clock input pin accepts the Serial Clock generated by the Master. SDA: The Serial Data I/O pin receives input data and transmits data stored in EEPROM. In transmit mode, this pin is open drain. Data is acquired on the positive edge, and is delivered on the negative edge of SCL. ...
Page 6
SCL SDA START CONDITION BUS RELEASE DELAY (TRANSMITTER) SCL FROM MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START t F SCL t SU:STA t SDA IN SDA OUT Figure 2. START/STOP Conditions DEVICE ADDRESS ...
Page 7
Write Operations Byte Write Upon receiving a Slave address with the R/W bit set to ‘0’, the CAT24C128 will interpret the next two bytes as address bytes. These bytes are used to initialize the internal address counter; the 2 most ...
Page 8
BUS ACTIVITY SLAVE R MASTER ADDRESS SLAVE Don’t Care Bit SCL a SDA 7 WP Read Operations Immediate Read Upon receiving a Slave address ...
Page 9
BUS ACTIVITY: MASTER SLAVE SCL SDA Figure 10. Immediate Read Sequence and Timing BUS ACTIVITY SLAVE R MASTER ADDRESS SLAVE Don’t Care Bit BUS ACTIVITY: SLAVE MASTER ADDRESS A SLAVE ...
Page 10
PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...
Page 11
PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...
Page 12
E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...
Page 13
D E PIN #1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.45 0.50 A1 0.00 0.02 A3 0.127 REF b 0.20 0.25 D 1.90 2.00 D2 1.50 1.60 E 2.90 3.00 E2 0.10 0.20 e 0.50 TYP K 0.10 ...
Page 14
E E1 TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD−01 ISSUE O SYMBOL MIN A A1 ...
Page 15
D E PIN #1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.45 0.50 A1 0.00 0.02 A3 0.127 REF b 0.20 0.25 D 1.95 2.00 D2 1.35 1.40 E 2.95 3.00 E2 1.25 1.30 e 0.50 REF L 0.25 ...
Page 16
... For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 18. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com 19 ...