CAT24C256YIGT3JN ON Semiconductor, CAT24C256YIGT3JN Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT24C256YIGT3JN
Specifications of CAT24C256YIGT3JN
Related parts for CAT24C256YIGT3JN
CAT24C256YIGT3JN Summary of contents
Page 1
... I C CMOS Serial EEPROM Description The CAT24C256 is a 256 kb Serial CMOS EEPROM, internally organized as 32,768 words of 8 bits each. It features a 64−byte page write buffer and supports the Standard (100 kHz), Fast (400 kHz) and Fast−Plus (1 MHz) I Write operations can be inhibited by taking the WP pin High (this protects the entire memory) ...
Page 2
Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Storage Temperature Voltage on any Pin with Respect to Ground (Note 1) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is ...
Page 3
Table 5. D.C. OPERATING CHARACTERISTICS − New Product (Rev 1 5 −40°C to +85°C and Symbol Parameter I Read Current Read, f CCR I Write Current CCW I Standby ...
Page 4
Table 7. A.C. CHARACTERISTICS − Mature Product (Rev 2 5 −40°C to +125°C, and Symbol Parameter F Clock Frequency SCL t START Condition Hold Time HD:STA t Low Period ...
Page 5
Table 9. A.C. CHARACTERISTICS − New Product (Rev 1 5 −40°C to +85°C and Symbol Parameter F Clock Frequency SCL t START Condition Hold Time HD:STA t Low Period ...
Page 6
... SCL: The Serial Clock input pin accepts the Serial Clock signal generated by the Master. SDA: The Serial Data I/O pin receives input data and transmits data stored in EEPROM. In transmit mode, this pin is open drain. Data is acquired on the positive edge, and is delivered on the negative edge of SCL. ...
Page 7
SCL SDA START CONDITION BUS RELEASE DELAY (TRANSMITTER) SCL FROM 1 MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START LOW SCL t SU:STA t HD:STA SDA IN SDA OUT Figure 2. Start/Stop Timing 1 0 ...
Page 8
WRITE OPERATIONS Byte Write In Byte Write mode the Master sends a START, followed by Slave address, two byte address and data to be written (Figure 6). The Slave acknowledges all 4 bytes, and the Master then follows up with ...
Page 9
BUS ACTIVITY: SLAVE R MASTER ADDRESS T SDA LINE Don’t Care Bit SCL SDA 8th Bit Byte n S BUS T ACTIVITY: A SLAVE MASTER R ADDRESS A − SDA ...
Page 10
READ OPERATIONS Immediate Address Read In standby mode, the CAT24C256 internal address counter points to the data byte immediately following the last byte accessed by a previous operation. If that ‘previous’ byte was the last byte in memory, then the ...
Page 11
PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...
Page 12
PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...
Page 13
E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...
Page 14
D E PIN #1 IDENTIFICATION TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A2 0.45 0.55 A3 0.20 REF b 0.25 0.30 D 2.90 3.00 D2 0.90 1.00 E 4.80 4.90 E2 0.90 1.00 e 0.65 TYP ...
Page 15
PIN#1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with EIAJ EDR-7320. PACKAGE DIMENSIONS SOIC−8, 208 mils CASE 751BE−01 ISSUE O SYMBOL ...
Page 16
D E PIN #1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.45 0.50 A1 0.00 0.02 A3 0.127 REF b 0.20 0.25 D 1.95 2.00 D2 1.35 1.40 E 2.95 3.00 E2 1.25 1.30 e 0.50 REF L 0.25 ...
Page 17
E E1 TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-187. PACKAGE DIMENSIONS MSOP 8, 3x3 CASE 846AD−01 ISSUE O SYMBOL MIN A A1 ...
Page 18
... For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 22. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com 23 ...