AT25DL081-MHN-Y Adesto Technologies, AT25DL081-MHN-Y Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
AT25DL081-MHN-Y
Manufacturer Part Number
AT25DL081-MHN-Y
Description
Flash 8M 1.65-1.95V 100Mhz Serial Flash
Manufacturer
Adesto Technologies
Datasheet
1.AT25DL081-MHN-T.pdf
(59 pages)
Specifications of AT25DL081-MHN-Y
Rohs
yes
Data Bus Width
8 bit
Memory Type
Flash
Memory Size
8 Mbit
Architecture
Flexible, Uniform Erase
Timing Type
Synchronous
Interface Type
SPI
Supply Voltage - Max
1.95 V
Supply Voltage - Min
1.65 V
Maximum Operating Current
20 mA
Operating Temperature
- 40 C to + 85 C
Mounting Style
SMD/SMT
Package / Case
UDFN-8
10.2
Figure 10-1. Sector Lockdown
Freeze Sector Lockdown State
The current sector lockdown state can be permanently frozen so that no further modifications to the Sector Lockdown
Registers can be made; therefore, the Sector Lockdown command will be permanently disabled and no additional
sectors can be locked down aside from those already locked down. Any attempts to issue the Sector Lockdown
command after the sector lockdown state has been frozen will be ignored.
Before the Freeze Sector Lockdown State command can be issued, the Write Enable command must have been
previously issued to set the WEL bit in the Status Register to a Logical 1. In addition, the Sector Lockdown Enabled
(SLE) bit in the Status Register must have also been previously set to the Logical 1 state. To issue the Freeze Sector
Lockdown State command, the CS pin must first be asserted and then the opcode 34h must be clocked into the device
followed by three command-specific address bytes of 55AA40h. After the three address bytes have been clocked in, a
confirmation byte of D0h must be clocked in immediately following the three address bytes. Any additional data clocked
into the device will be ignored. When the CS pin is deasserted, the current sector lockdown state will be permanently
frozen within a time of t
the SLE bit will be permanently reset to a Logical 0 to indicate that the Sector Lockdown command is permanently
disabled.
The three complete and correct address bytes and the confirmation byte must be clocked into the device before the CS
pin is deasserted, and the CS pin must be deasserted on an even byte boundary (multiples of eight bits); otherwise, the
device will abort the operation. When the device aborts the Freeze Sector Lockdown State operation, the WEL bit in the
Status Register will be reset to a Logical 0; however, the state of the SLE bit will be unchanged.
Figure 10-2. Freeze Sector Lockdown State
SCK
SCK
SO
CS
SO
CS
SI
SI
MSB
High-impedance
MSB
High-impedance
0
0
0
0
0
0
1
1
LOCK
1
1
2
2
Opcode
Opcode
1
1
. In addition, the WEL bit in the Status Register will be reset back to the Logical 0 state, and
3
3
0
0
4
4
0
1
5
5
1
0
6
6
1
0
7
7
MSB
MSB
A
0
8
8
Address Bits A23-A0
Address Bits A23-A0
A
1
9
9
A
0
A
0
29 30
29 30
A
0
A
0
31 32
31 32
MSB
MSB
1
1
Confirmation Byte In
Confirmation Byte In
1
1
33
33
0
0
34
34
1
35
1
35
0
0
36
36
0
37 38
0
37 38
0
0
0
0
39
39
AT25DL081 [DATASHEET]
8732E–DFLASH–1/2013
30