PCA9535ECDTR2G ON Semiconductor, PCA9535ECDTR2G Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
PCA9535ECDTR2G
Specifications of PCA9535ECDTR2G
Available stocks
Related parts for PCA9535ECDTR2G
PCA9535ECDTR2G Summary of contents
Page 1
PCA9535E, PCA9535EC 16-bit Low-Power I/O 2 Expander for I C Bus with Interrupt The PCA9535E and PCA9535EC devices provide 16 bits of General Purpose parallel Input / Output (GPIO) expansion through the 2 I C−bus / SMBus. The PCA9535E and ...
Page 2
PCA9535E PCA9535EC AD0 AD1 AD2 SCL INPUT FILTER SDA V DD POWER−ON RESET V SS data from shift register configuration register data from D Q shift register FF write configuration CK Q pulse write pulse read pulse data from shift ...
Page 3
INT 1 AD1 2 3 AD2 IO0_0 4 IO0_1 5 PCA9535E 6 IO0_2 PCA9535EC IO0_3 7 IO0_4 8 IO0_5 9 10 IO0_6 IO0_7 Figure 3. SOIC24 / TSSOP24 Table 1. PIN DESCRIPTIONS SOIC24, TSSOP24 Symbol INT ...
Page 4
Table 2. MAXIMUM RATINGS Symbol V DC Supply Voltage DD V Input / Output Pin Voltage I/O I Input Current I I Output Current Supply Current Ground Current GND P Total Power Dissipation TOT ...
Page 5
Table 4. DC ELECTRICAL CHARACTERISTICS Symbol Parameter SUPPLIES I Standby Current (Note 6) STB V Power−On Reset Voltage (Note 7) POR INPUT SCL; INPUT / OUTPUT SDA V High−Level Input Voltage IH V Low−Level Input Voltage IL I Low−Level Output ...
Page 6
Table 5. AC ELECTRICAL CHARACTERISTICS Symbol Parameter f SCL Clock Frequency SCL t Bus−Free Time between a STOP and START BUF Condition t Hold Time (Repeated) START Condition HD:STA t Setup Time for a Repeated START Condition SU:STA t Setup ...
Page 7
Device Address Before the bus master can access a slave device, it must send the address of the slave it is accessing and the operation it wants to perform (read or write) following a START condition. The slave address of ...
Page 8
Table 6. PCA9535E AND PCA9535EC ADDRESS MAP Address Input AD2 AD1 AD0 VDD VDD SDA SCL SCL GND SCL SCL VDD SCL SDA GND SCL SDA VDD SDA SCL GND SDA SCL VDD SDA SDA GND SDA SDA VDD SCL ...
Page 9
Command Byte During a write transmission, the address byte is followed by the command byte. The command byte determines which of the following registers will be written or read. Table 7. COMMAND BYTE COMMAND 0 Input Port 0 1 Input ...
Page 10
Registers 4 and 5: Polarity Inversion Registers These registers allow the polarity of the data in the input port registers to be inverted. The input port data polarity will Table 12. POLARITY INVERSION PORT 0 REGISTER Bit 7 6 Symbol ...
Page 11
Writing to the Port Registers To transmit data to the PCA9535E/PCA9535EC, the bus master must first send the device address with the least significant bit set to logic 0 (see Figure 5 “PCA9535E and PCA9535EC device address”). The command byte ...
Page 12
SDA START condition R/W acknowledge from slave slave address (cont (repeated) R/W START condition acknowledge from slave Remark: Transfer can ...
Page 13
Interrupt Output The open−drain interrupt output is activated when an I/O pin configured as an input changes state. The interrupt is deactivated when the input pin returns to its previous state or when the Input Port register is read (see ...
Page 14
V DD LED LEDn Figure 12. High Value Resistor in Parallel with the LED 2 Characteristics of the I C−bus 2 The I C−bus is meant for 2−way, 2−line communication between different ICs or modules. The two lines are the ...
Page 15
System Configuration A device generating a message is a ‘transmitter’; a device receiving is the ‘receiver’. The device that controls the SDA SCL MASTER SLAVE TRANSMITTER/ RECEIVER RECEIVER Acknowledge The number of data bytes transferred between the START and the ...
Page 16
START bit 7 protocol condition MSB (S) (A7 SU;STA LOW HIGH SCL t BUF t r SDA t HD;STA Rise and fall times refer to V and Figure 19. I SCL t v(Q) IOn ...
Page 17
... ORDERING INFORMATION Device PCA9535EDWR2G PCA9535EDTR2G PCA9535EMTTXG PCA9535ECDWR2G PCA9535ECDTR2G PCA9535ECMTTXG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Package SOIC−24 (Pb−Free) TSSOP−24 (Pb−Free) WQFN24 (Pb−Free) SOIC−24 (Pb− ...
Page 18
D 24X 0.010 (0.25 −T− SEATING G PLANE 22X PACKAGE DIMENSIONS SOIC−24 CASE 751E−04 ISSUE E 13 −B− P 12X 0.010 (0.25 ...
Page 19
L PIN 1 IDENT. 1 0.15 (0.006 0.10 (0.004) −T− SEATING D PLANE K K1 Ç Ç Ç Ç Ç Ç É É É J1 Ç Ç Ç ...
Page 20
... 0.05 C NOTE 3 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81− ...