MAX4313EVKIT Maxim Integrated, MAX4313EVKIT Datasheet

MAX4313EVKIT

Manufacturer Part Number

MAX4313EVKIT

Description

Video Amplifiers Programmers, Development Systems

Manufacturer

Maxim Integrated

Datasheet

1.MAX4313EVKIT.pdf (4 pages)

Specifications of MAX4313EVKIT

Number Of Channels

Operating Supply Voltage

12 V

Supply Current

560 uA

Bandwidth

40 MHz

Maximum Dual Supply Voltage

5.25 V

Minimum Dual Supply Voltage

2 V

Factory Pack Quantity

Supply Voltage - Max

10.5 V

Supply Voltage - Min

4 V

Current page: 1 of 4
Download datasheet (107Kb)

The MAX4313 evaluation kit (EV kit) simplifies evalua-

tion of the MAX4313 low-power, single-supply video

multiplexer/amplifier. The MAX4313 is fixed to a gain of

+2V/V, ideal for driving back-terminated cables. SMA

connectors and 50Ω terminating resistors are included

for 50Ω test equipment compatibility. Simply change

the terminating resistors to 75Ω for video test equip-

ment compatibility.

The EV kit comes with the MAX4313 installed. To evaluate

the MAX4310, simply order a free sample (MAX4310ESA),

replace the MAX4313 with the MAX4310 on the EV board,

and change the gain-setting resistors for the desired gain.

19-1379; Rev 1; 4/99

Note: Please indicate that you are using the MAX4313 when

For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.

For small orders, phone 408-737-7600 ext. 3468.

DESIGNATION

IN0, IN1, OUT

AVX

Sprague

JU1, JU2

C1, C3

C2, C4

R1–R3

SUPPLIER

None

contacting these component suppliers.

QTY

________________________________________________________________ Maxim Integrated Products

0.1µF, 10% ceramic capacitors

10µF, 10V, 20% tantalum capacitors

AVX TAJB106M010 or

Sprague 293D106X0010B

49.9

Not installed

SMA connectors

3-pin headers

MAX4313ESA

Shunts for JU1, JU2

MAX4313 EV kit PC board

Component Suppliers

803-946-0690

603-224-1961

Ω

General Description

resistor

PHONE

Ω

, 1% resistors

Component List

DESCRIPTION

803-626-3123

603-224-1430

FAX

MAX4313 Evaluation Kit

The MAX4313 EV kit is fully assembled and tested. Fol-

low these steps to verify board operation.

1) The circuit requires supply voltages of +4.5V to

2) Connect the output labeled OUT to an oscilloscope

3) Place the shunt across pins 2 and 3 of jumper JU2

4) Turn on the power supply. Apply a ±0.5V signal

5) Verify the output signal on the oscilloscope.

Note: To evaluate the MAX4310, request a MAX4310ESA free

MAX4313EVKIT

Single-Supply Operation

150MHz -3dB Bandwidth (R

540V/µs Slew Rate (R

40MHz 0.1dB Gain Flatness (R

Low Switching Transient (20mVp-p)

0.06%/0.02° Gain/Phase Errors

Outputs Extend to the Rails

Fully Assembled and Tested Surface-Mount Board

+10.5V. For evaluation purposes, connect a +5V

supply to the pad labeled VCC and connect the

power-supply ground to the pads labeled VEE and

GND.

input. Set the shunt across the appropriate pins of

jumper JU1 to select a multiplexer input (IN0 or

IN1).

to enable the MAX4313’s output.

with V

input selected in Step 2. The 100Ω load (chosen for

ease of evaluation) limits the output voltage range.

Wider output voltage swings are achievable with

lighter loads. See the MAX4310/MAX4313 data

sheet.

PART

sample.

= +1.5V to the appropriate multiplexer

TEMP. RANGE

-40°C to +85°C

Ordering Information

= 150Ω)

Quick Start

IC PACKAGE

8 SO

Features

Related parts for MAX4313EVKIT

MAX4313EVKIT Summary of contents

Page 1

... Low Switching Transient (20mVp-p) 0.06%/0.02° Gain/Phase Errors Outputs Extend to the Rails Fully Assembled and Tested Surface-Mount Board PART MAX4313EVKIT Note: To evaluate the MAX4310, request a MAX4310ESA free sample. The MAX4313 EV kit is fully assembled and tested. Fol- low these steps to verify board operation. ...

Page 2

MAX4313 Evaluation Kit Detailed Description Setting the Voltage Gain (MAX4310) The gain of the MAX4310’s amplifier can be set by changing the feedback (R ) and gain-set (R F tors. Refer to the MAX4310/MAX4313 data sheet for recommended values. Control ...

Page 3

Figure 2. MAX4313 EV Kit Component Placement Guide— Component Side 1.0" Figure 3. MAX4313 EV Kit PC Board Layout Guide— Component Side _______________________________________________________________________________________ MAX4313 Evaluation Kit 1.0" 1.0" Figure 4. MAX4313 EV Kit PC Board Layout Guide—Solder Side 3 ...

Page 4

... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 4 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 1999 Maxim Integrated Products ...

Related keywords

MAX4313EVKIT datasheet
MAX4313EVKIT data sheet
MAX4313EVKIT pdf datasheet
MAX4313EVKIT component
MAX4313EVKIT part
MAX4313EVKIT distributor
MAX4313EVKIT RoHS
MAX4313EVKIT datasheet download