DS21458-W+ Maxim Integrated, DS21458-W+ Datasheet - Page 68
DS21458-W+
Manufacturer Part Number
DS21458-W+
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS21458-W.pdf
(269 pages)
Specifications of DS21458-W+
Product
Framer
Number Of Transceivers
4
Data Rate
64 Kbps
Supply Current (max)
328 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
CSBGA
Minimum Operating Temperature
0 C
Operating Supply Voltage
3.3 V
Supply Voltage - Max
3.465 V
Supply Voltage - Min
3.135 V
Part # Aliases
90-21458+W00
- Current page: 68 of 269
- Download datasheet (2Mb)
11.2 Automatic Alarm Generation
The device can be programmed to automatically transmit AIS or remote alarm.
11.2.1 Auto AIS
When automatic AIS generation is enabled (E1TCR2.1 = 1), the device monitors the receive side framer
to determine if any of the following conditions are present: loss of receive frame synchronization, AIS
alarm (all ones) reception, or loss of receive carrier (or signal). If any one (or more) of the above
conditions is present, then the framer will either force an AIS or remote alarm.
11.2.2 Auto RAI
When automatic RAI generation is enabled (E1TCR2.0 = 1), the framer monitors the receive side to
determine if any of the following conditions are present: loss of receive frame synchronization, AIS alarm
(all ones) reception, or loss of receive carrier (or signal) or if CRC-4 multiframe synchronization cannot
be found within 128ms of FAS synchronization (if CRC-4 is enabled). If any one (or more) of the above
conditions is present, then the framer will transmit a RAI alarm. RAI generation conforms to ETS 300
011 specifications and a constant remote alarm will be transmitted if the DS21455/DS21458 cannot find
CRC-4 multiframe synchronization within 400ms as per G.706.
Note: It is an illegal state to have both automatic AIS generation and automatic remote alarm
generation enabled at the same time.
11.2.3 Auto E-Bit
When automatic E-Bit generation is enabled (E1TCR2.2 = 1), and the transmitter is in CRC-4 mode, the
transmitter will automatically set the E-Bit according to the following.
Table 11-2. Auto E-Bit Conditions
Receive CRC-4 disabled
Receive CRC-4 enabled but not synchronized
Receive CRC-4 enabled, Synchronized, with CRC Sub Multiframe codeword error
Receiver synchronized in CRC-4 mode with no CRC Sub Multiframe codeword errors
11.2.4 G.706 CRC-4 Interworking
G.706 Specifies a method to allow automatic interworking between equipment with and without CRC-4
capability. When basic frame alignment is established the device begins searching for the CRC-4
alignment pattern. If after 8ms the CRC-4 alignment is not found, it is assumed that frame alignment was
invalid and the device returns to the basic frame alignment search to establish new frame alignment.
After the new frame alignment is established the device starts a new 8ms search period for CRC-4
alignment. If CRC-4 alignment is found, the device starts CRC-4 performance monitoring and setting of
the transmitted E-bits according to G.706. (See the Auto E-bit section.) If CRC-4 alignment is not
achieved the device continues to return to the basic frame alignment procedure followed by an 8ms
search period for CRC-4. This process continues for 400ms. At the end of this 400ms period, it is
assumed that the far end equipment is non-CRC-4, the search for CRC-4 alignment is terminated and the
E-bits transmitter toward the far end equipment are set continuously = 0. The DS21455/DS21458 provide
a flexible method for implementing this procedure. Once the device is put into the receive CRC-4 mode, a
counter begins to run. The user can access this counter via Information Register 7.
CONDITION
68 of 269
DS21455/DS21458 Quad T1/E1/J1 Transceivers
STATE
E-BIT
0
0
0
1
Related parts for DS21458-W+
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC LIU QUAD T1/E1/J1 256-CSBGA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Network Controller & Processor ICs Quad E1-T1-J1 Single -Chip Transceiver (S
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
power light source Luxeon Line
Manufacturer:
LUMILEDS [Lumileds Lighting Company]
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products