25AA020AT-I/OT Microchip Technology, 25AA020AT-I/OT Datasheet
25AA020AT-I/OT
Specifications of 25AA020AT-I/OT
Available stocks
Related parts for 25AA020AT-I/OT
25AA020AT-I/OT Summary of contents
Page 1
... Bytes I 16 Bytes I, E Description: The Microchip Technology Inc. 25XX020A Kbit Serial Electrically Erasable Programmable Read-Only Memory (EEPROM). The memory is accessed via a simple Serial Peripheral Interface (SPI) compatible serial bus. The bus signals required are a clock input (SCK) plus separate data in (SI) and data out (SO) lines ...
Page 2
... Test Conditions ≥ 2.7V (Note 1) < 2.7V (Note 1.0 mA, V < 2. -400 μ OUT 5.0V (Note 1) = 5.5V 10.0 MHz; CLK = 2.5V 5.0 MHz; CLK = 5.5V = 2.5V = 5.5V, Inputs tied +125° 2.5V, Inputs tied +85°C A © 2007 Microchip Technology Inc. ...
Page 3
... Total Endurance™ Model which can be obtained from Microchip’s web site at www.Microchip.com begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle WC is complete. © 2007 Microchip Technology Inc. 25AA020A/25LC020A Industrial (I -40°C to +85°C A ...
Page 4
... E/W (N Cycles — (Note 1) (Note 2) — Preliminary V = 1. 2.5V to 5.5V CC Test Conditions < 5.5V CC < 4.5V CC < 2.5V CC < 5.5V (Note 1) CC < 4.5V (Note 1) CC < 2.5V (Note 1) CC < 5.5V CC < 4.5V CC < 2. OTE © 2007 Microchip Technology Inc. ...
Page 5
... SI HOLD FIGURE 1-2: SERIAL INPUT TIMING CS 2 Mode 1,1 Mode 0,0 SCK MSB in SO FIGURE 1-3: SERIAL OUTPUT TIMING SCK 13 MSB out SO SI © 2007 Microchip Technology Inc. 25AA020A/25LC020A High-Impedance n Don’t Care High-Impedance 14 Don’t Care Preliminary LSB in 3 Mode 1,1 ...
Page 6
... Attempting to read a memory array location will not be possible during a write cycle. Polling the WIP bit in the STATUS register is recommended in order to determine if a write cycle is in progress. When the write cycle is completed, the write enable latch is reset. Preliminary © 2007 Microchip Technology Inc. ...
Page 7
... Instruction High-Impedance SO © 2007 Microchip Technology Inc. 25AA020A/25LC020A HV Generator EEPROM Array Page Latches Y Decoder Sense Amp. R/W Control Read data from memory array beginning at selected address Write data to memory array beginning at selected address Reset the write enable latch (disable write operations) ...
Page 8
... FIGURE 2-2: BYTE WRITE SEQUENCE SCK Instruction FIGURE 2-3: PAGE WRITE SEQUENCE SCK Instruction SCK Data Byte DS21833D-page Address Byte High-Impedance Address Byte Data Byte Preliminary Twc Data Byte Data Byte Data Byte n (16 max © 2007 Microchip Technology Inc. ...
Page 9
... SI SO FIGURE 2-5: WRITE DISABLE SEQUENCE (WRDI) CS SCK SI SO © 2007 Microchip Technology Inc. 25AA020A/25LC020A The following is a list of conditions under which the write enable latch will be reset: • Power-up See • WRDI instruction successfully executed • WRSR instruction successfully executed • ...
Page 10
... These bits are set by the user issuing the WRSR instruction, which shown in Figure 2-7. These bits are nonvolatile and R R are described in more detail in Table 2-3. WEL WIP ’, no write Data from STATUS register Preliminary © 2007 Microchip Technology Inc. ...
Page 11
... Table 2-3. FIGURE 2-7: WRITE STATUS REGISTER TIMING SEQUENCE (WRSR SCK Instruction Note: An internal write cycle (T WC sequence. © 2007 Microchip Technology Inc. 25AA020A/25LC020A TABLE 2-3: BP1 Data to STATUS register ...
Page 12
... The device is in low-power Standby mode ( • The write enable latch is reset • high-impedance state • A high-to-low-level transition required to enter active state Protected Blocks Unprotected Blocks Protected Protected Protected Protected Protected Writable Preliminary STATUS Register Protected Protected Writable © 2007 Microchip Technology Inc. ...
Page 13
... Serial Input (SI) The SI pin is used to transfer data into the device. It receives instructions, addresses and data. Data is latched on the rising edge of the serial clock. © 2007 Microchip Technology Inc. 25AA020A/25LC020A 3.5 Serial Clock (SCK) The SCK is used to synchronize the communication between a master and the 25XX020A. Instructions, ...
Page 14
... Example: 5A2A I627 1L7 Example: 5L2AI 6271L7 1st Line Marking Codes MSOP SOT-23 Rotated I Temp. E Temp. — 22NN A2AX 5A2AT L2AX 5L2AT 25NN 26NN NN = Alphanumeric traceability code Preliminary DFN I Temp. E Temp. — 411 414 415 ) e 3 © 2007 Microchip Technology Inc. ...
Page 15
... Package Marking Information (continued) 8-Lead 2X3 DFN XXX YWW NN 6-Lead SOT-23 XXNN © 2007 Microchip Technology Inc. 25AA020A/25LC020A Example: 411 627 L7 Example: 22L7 Preliminary DS21833D-page 15 ...
Page 16
... N NOTE DS21833D-page Preliminary c © 2007 Microchip Technology Inc. ...
Page 17
... N NOTE © 2007 Microchip Technology Inc. 25AA020A/25LC020A φ Preliminary α c β DS21833D-page 17 ...
Page 18
... DS21833D-page 18 Preliminary © 2007 Microchip Technology Inc. ...
Page 19
... D N NOTE © 2007 Microchip Technology Inc. 25AA020A/25LC020A Preliminary φ L DS21833D-page 19 ...
Page 20
... D N NOTE DS21833D-page Preliminary φ L © 2007 Microchip Technology Inc. ...
Page 21
... D N NOTE TOP VIEW A3 © 2007 Microchip Technology Inc. 25AA020A/25LC020A EXPOSED PAD BOTTOM VIEW A NOTE 2 A1 Preliminary NOTE DS21833D-page 21 ...
Page 22
... N PIN LASER MARK DS21833D-page Preliminary φ © 2007 Microchip Technology Inc. ...
Page 23
... REVISION HISTORY Revision B Corrections to Section 1.0, Electrical Characteristics. Revision C Added Packages SOT-23, DFN and X-rotated TSSOP; Revised AC Char., Params. 9, 10; Revised Package Legend. Revision D Revised Features (Pb-free); Replaced Package Drawings; Revised Product ID System. © 2007 Microchip Technology Inc. 25AA020A/25LC020A Preliminary DS21833D-page 23 ...
Page 24
... NOTES: DS21833D-page 24 Preliminary © 2007 Microchip Technology Inc. ...
Page 25
... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2007 Microchip Technology Inc. 25AA020A/25LC020A CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • ...
Page 26
... What deletions from the document could be made without affecting the overall usefulness there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS21833D-page 26 Total Pages Sent ________ FAX: (______) _________ - _________ N Literature Number: DS21833D Preliminary © 2007 Microchip Technology Inc. ...
Page 27
... Examples: Package a) 25AA020A-I/MS = 2k-bit, 16-byte page, 1.8V Serial EEPROM, Industrial temp., MSOP package b) 25AA020AT-I/SN = 2k-bit, 16-byte page, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package c) 25LC020AT-I/SN = 2k-bit, 16-byte page, 2.5V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package d) 25LC020AT-I/ST = 2k-bit, 16-byte page, 2 ...
Page 28
... NOTES: DS21833D-page 28 Preliminary © 2007 Microchip Technology Inc. ...
Page 29
... PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 30
... Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Preliminary © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...