ICL7106EPL+ Maxim Integrated, ICL7106EPL+ Datasheet - Page 2

• Manufacturer Part Number: ICL7106EPL+
• Description: Display Drivers & Controllers CMOS Analog MUX
• Manufacturer: Maxim Integrated
• Series: ICL7106, ICL7107r

ICL7106/ICL7107
3
Supply Voltage
Analog Input Voltage (either input) (Note 1) ................. V+ to V-
Reference Input Voltage (either input) ...........................V+ to V-
Clock Input
ABSOLUTE MAXIMUM RATINGS
Note 1: Input voltages may exceed the supply voltages, provided the input current is limited to ±100µA.
Note 2: Dissipation rating assumes device is mounted with all leads soldered to the PCB.
ELECTRICAL CHARACTERISTICS
(Note 3)
The electrical characteristics above are a reproduction of a portion of Intersil's copyrighted (1983/1984) data book. This information
does not constitute any representation by Maxim that Intersil's products will perform in accordance with these specifications. The
"Electrical Characteristics table" along with the descriptive excerpts from the original manufacturer's data sheet have been included
in this data sheet solely for comparative purposes.
2
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Zero Input Reading
Ratiometric Reading
Rollover Error (Difference in Reading for
Equal Positive and Negative Reading Near
Full Scale)
Linearity (Maximum Deviation from Best
Straight Line Fit)
Common-Mode Rejection Ratio (Note 4)
Noise (Pk-Pk Value Not Exceeded
95% of Time)
Input Leakage Current
Zero Reading Drift
Scale Factor Temperature Coefficient
V+ Supply Current (Does Not Include LED
Current for ICL7107)
V- Supply Current (ICL7107 Only)
Analog Common Voltage
(With Respect to Positive Supply)
Temperature Coefficient of Analog
Common (With Respect to Positive Supply)
ICL7106, V+ to V- ..............................................................15V
ICL7107, V+ to GND ........................................................ +6V
ICL7107, V- to GND ...........................................................-9V
ICL7106 .................................................................TEST to V+
ICL7107 ................................................................. GND to V+
1
⁄
2
Digit A/D Converters
PARAMETER
V
V
-V
Full scale = 200mV or full scale = 2.000V
V
V
V
V
V
(external reference 0ppm/NC)
V
25kI between common and positive supply
25kI between common and positive supply
IN
IN
CM
IN
IN
IN
IN
IN
IN
= 0V, full scale = 200.0mV
= V
= 0V, full scale = 200mV
= 0V
= 0V, 0NC < T
= 199.0mV, 0NC < T
= 0V
= +V
= Q1V, V
REF
IN
, V
= 200.0mV
REF
IN
= 0V, full scale = 200.0mV
CONDITIONS
A
= 100mV
< +70NC
Continuous Power Dissipation (T
Operating Temperature Range ............................. 0NC to +70NC
Storage Temperature Range ............................ -55NC to +160NC
Lead Temperature (soldering, 10s) ................................+300NC
Soldering Temperature (reflow)
A
PDIP (derate 16.7mW/NC above +70NC) ................1333.3mW
PLCC (derate 13.3mW/NC above +70NC)...............1066.7mW
PDIP .............................................................................+260NC
PLCC ...........................................................................+245NC
< +70NC
-000.0
MIN
999
2.4
-1
-1
A
999/1000 1000
= +70NC)(Note 2)
000.0
TYP
0.2
0.8
0.6
2.8
Q2
Q2
50
15
80
1
1
+000.0
MAX
Maxim Integrated
1.8
1.8
3.2
+1
+1
10
1
5
Reading
Reading
ppm/NC
ppm/NC
Counts
Counts
UNITS
Digital
Digital
FV/NC
FV/V
mA
mA
pA
FV
V