LYT4312E Power Integrations, LYT4312E Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/5/532/power_integrations_sml.jpg)
LYT4312E
Manufacturer Part Number
LYT4312E
Description
LED Lighting Drivers HighPower LED Driver 15W Dimmable
Manufacturer
Power Integrations
Datasheet
1.LYT4316E.pdf
(20 pages)
Specifications of LYT4312E
Rohs
yes
Input Voltage
85 V to 132 V
Operating Frequency
124 kHz to 140 kHz
Maximum Supply Current
3 mA
Output Current
1.17 A
Maximum Operating Temperature
+ 150 C
Mounting Style
Through Hole
Package / Case
eSIP-7C
Minimum Operating Temperature
- 40 C
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LYT4312E
Manufacturer:
POWER
Quantity:
15 000
Part Number:
LYT4312E
Manufacturer:
POWER
Quantity:
20 000
Functional Description
A LYTSwitch device monolithically combines a controller and
high-voltage power FET into one package. The controller
provides both high power factor and constant current output in
a single-stage. The LYTSwitch controller consists of an
oscillator, feedback (sense and logic) circuit, 5.9 V regulator,
hysteretic over-temperature protection, frequency jittering,
cycle-by-cycle current limit, auto-restart, inductance correction,
power factor and constant current control.
FEEDBACK Pin Current Control Characteristics
The figure shown below illustrates the operating boundaries of
the FEEDBACK pin current. Above I
and below I
Figure 6.
The FEEDBACK pin current is also used to clamp the maximum
duty cycle to limit the available output power for overload and
open-loop conditions. This duty cycle reduction characteristic
also promotes a monotonic output current start-up characteristic
and helps preventing over-shoot.
REFERENCE Pin
The REFERENCE pin is tied to ground (SOURCE) via an external
resistor. The value selected sets the internal references,
determining the operating mode for dimming (LYT4311-4318)
and non-dimming (LYT4211-4218) operation and the line
overvoltage thresholds of the VOLTAGE MONITOR pin. For
Rev. B 02/13
LYT4211-4218/4311-4318
4
I
FB(DCMAXR)
I
FB(SKIP)
I
FB(AR)
FEEDBACK Pin Current Characteristic.
I
FB
FB(AR)
the device enters into auto-restart.
Soft-Start and
CC Fold-Back
Region
DC10
Maximum Duty Cycle
CC Control
Auto-Restart
Skip-Cycle
Region
FB(SKIP)
switching is disabled
DC
PI-5433-060410
MAX
non-dimming or PWM dimming applications with LYT4211-4218,
the external resistor should be a 24.9 kW ±1%. For phase angle
AC dimming with LYT4311-4318, the external resistor should be
a 49.9 kW ±1%. One percent resistors are recommended as
the resistor tolerance directly affects the output tolerance.
Other resistor values should not be used.
BYPASS Pin Capacitor Power Gain Selection
LYTSwitch devices have the capability to tailor the internal gain
to either full or a reduced output power setting. This allows
selection of a larger device to minimize dissipation for both
thermal and efficiency reasons. The power gain is selected with
the value of the BYPASS pin capacitor. The full power setting is
selected with a 4.7 µF capacitor and the reduced power setting
(for higher efficiency) is selected with a 47 µF capacitor. The
BYPASS pin capacitor sets both the internal power gain as well
as the over-current protection (OCP) threshold. Unlike the
larger devices, the LYT4x11 power gain is not programmable.
Use a 47 µF capacitor for the LYT4x11.
Switching Frequency
The switching frequency is 132 kHz during normal operation.
To further reduce the EMI level, the switching frequency is
jittered (frequency modulated) by approximately 2.6 kHz.
During start-up the frequency is 66 kHz to reduce start-up time
when the AC input is phase angle dimmed. Jitter is disabled in
deep dimming.
Soft-Start
The controller includes a soft-start timing feature which inhibits
the auto-restart protection feature for the soft-start period (t
to distinguish start-up into a fault (short-circuit) from a large
output capacitor. At start-up the LYTSwitch clamps the
maximum duty cycle to reduce the output power. The total
soft-start period is t
Remote ON/OFF and EcoSmart
The VOLTAGE MONITOR pin has a 1 V threshold comparator
connected at its input. This voltage threshold is used for
remote ON/OFF control. When a signal is received at the
VOLTAGE MONITOR pin to disable the output (VOLTAGE
MONITOR pin tied to ground through an optocoupler photo-
transistor) the LYTSwitch will complete its current switching
cycle before the internal power FET is forced off.
The remote ON/OFF feature can also be used as an eco-mode
or power switch to turn off the LYTSwitch and keep it in a very
low power consumption state for indefinite long periods. When
the LYTSwitch is remotely turned on after entering this mode, it
will initiate a normal start-up sequence with soft-start the next
time the BYPASS pin reaches 5.9 V. In the worst case, the
delay from remote on to start-up can be equal to the full
discharge/charge cycle time of the BYPASS pin. This reduced
consumption remote off mode can eliminate expensive and
unreliable in-line mechanical switches.
SOFT
.
™
www.powerint.com
SOFT
)