25AA160D-I/P Microchip Technology, 25AA160D-I/P Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
25AA160D-I/P
Manufacturer Part Number
25AA160D-I/P
Description
IC SRL EEPROM 2KX8 1.8V 8-PDIP
Manufacturer
Microchip Technology
Specifications of 25AA160D-I/P
Memory Size
16K (2K x 8)
Package / Case
8-DIP (0.300", 7.62mm)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
3MHZ, 5MHZ, 10MHZ
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Organization
2 K x 8
Interface Type
SPI
Maximum Clock Frequency
3 MHz
Access Time
160 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Current
5 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
25AA160/25LC160/25C160
2.0
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
2.1
A low level on this pin selects the device. A high level
deselects the device and forces it into Standby mode.
However, a programming cycle which is already initi-
ated or in progress will be completed, regardless of the
CS input signal. If CS is brought high during a program
cycle, the device will go into Standby mode as soon as
the programming cycle is complete. When the device is
deselected, SO goes to the high-impedance state,
allowing multiple parts to share the same SPI bus. A
low-to-high transition on CS after a valid write
sequence initiates an internal write cycle. After power-
up, a low level on CS is required prior to any sequence
being initiated.
2.2
The SO pin is used to transfer data out of the 25XX160.
During a read cycle, data is shifted out on this pin after
the falling edge of the serial clock.
2.3
This pin is used in conjunction with the WPEN bit in the
Status register to prohibit writes to the nonvolatile bits
in the Status register. When WP is low and WPEN is
high, writing to the nonvolatile bits in the Status register
is disabled. All other operations function normally.
When WP is high, all functions, including writes to the
nonvolatile bits in the Status register operate normally.
If the WPEN bit is set, WP low during a Status register
write sequence will disable writing to the Status
register. If an internal write cycle has already begun,
WP going low will have no effect on the write.
The WP pin function is blocked when the WPEN bit in
the Status register is low. This allows the user to install
the 25XX160 in a system with WP pin grounded and
still be able to write to the Status register. The WP pin
functions will be enabled when the WPEN bit is set
high.
DS21231D-page 6
CS
SO
WP
V
SI
SCK
HOLD
Vcc
Name
SS
PIN DESCRIPTIONS
Chip Select (CS)
Serial Output (SO)
Write-Protect (WP)
PDIP
1
2
3
4
5
6
7
8
PIN FUNCTION TABLE
SOIC
1
2
3
4
5
6
7
8
Chip Select Input
Serial Data Output
Write-Protect Pin
Ground
Serial Data Input
Serial Clock Input
Hold Input
Supply Voltage
Description
2.4
The SI pin is used to transfer data into the device. It
receives instructions, addresses and data. Data is
latched on the rising edge of the serial clock.
2.5
The SCK is used to synchronize the communication
between a master and the 25XX160. Instructions,
addresses, or data present on the SI pin are latched on
the rising edge of the clock input, while data on the SO
pin is updated after the falling edge of the clock input.
2.6
The HOLD pin is used to suspend transmission to the
25XX160 while in the middle of a serial sequence
without having to retransmit the entire sequence again.
It must be held high any time this function is not being
used. Once the device is selected and a serial
sequence is underway, the HOLD pin may be pulled
low to pause further serial communication without
resetting the serial sequence. The HOLD pin must be
brought low while SCK is low, otherwise the HOLD
function will not be invoked until the next SCK high-to-
low transition. The 25XX160 must remain selected
during this sequence. The SI, SCK, and SO pins are in
a high-impedance state during the time the device is
paused and transitions on these pins will be ignored. To
resume serial communication, HOLD must be brought
high while the SCK pin is low, otherwise serial commu-
nication will not resume. Lowering the HOLD line at any
time will tri-state the SO line.
Serial Input (SI)
Serial Clock (SCK)
Hold (HOLD)
2004 Microchip Technology Inc.