MAX5941BCSE-T Maxim Integrated, MAX5941BCSE-T Datasheet - Page 14

• Manufacturer Part Number: MAX5941BCSE-T
• Description: Power Switch ICs - POE / LAN
• Manufacturer: Maxim Integrated

During classification mode, if the PSE applies the maxi-
mum DC voltage, the maximum voltage drop from GND
to V
of 42mA flows through the MAX5941A/MAX5941B, then
the maximum DC power dissipation will be close to
546mW, which is slightly higher than the maximum DC
power dissipation of the IC at maximum operating tem-
perature. However, according to the IEEE 802.3af stan-
dard, the duration of the classification mode is limited to
75ms (max). The MAX5941A/MAX5941B handles the
maximum classification power dissipation for the maxi-
mum duration time without sustaining any internal dam-
age. If the PSE violates the IEEE 802.3af standard by
exceeding the 75ms maximum classification duration, it
may cause internal damage to the IC.
The MAX5941A/MAX5941B offer current-mode control
operation with added features such as leading-edge
blanking with dual internal path that only blanks the
sensed current signal applied to the input of the PWM
comparator. The current-limit comparator monitors the
CS pin at all times and provides cycle-by-cycle current
limit without being blanked. The leading-edge blanking
of the CS signal prevents the PWM comparator from
prematurely terminating the on cycle. The CS signal
contains a leading-edge spike that is the result of the
MOSFET gate charge current, capacitive and diode
reverse recovery current of the power circuit. Since this
leading-edge spike is normally lower than the current
limit comparator threshold, current limiting is not
blanked and cycle-by-cycle current limiting is provided
under all conditions.
Use the MAX5941A in discontinuous flyback applica-
tions where wide line voltage and load current variation
is expected. Use the MAX5941B for single transistor
forward converters where the maximum duty cycle must
be limited to less than 50%.
Under certain conditions, it may be advantageous to
use a forward converter with greater than 50% duty
cycle. For those cases, use the MAX5941A. The large
duty cycle results in much lower operating primary RMS
currents through the MOSFET switch and in most cases
a smaller output filter inductor. The major disadvantage
to this is that the MOSFET voltage rating must be higher
and that slope compensation must be provided to sta-
bilize the inner current loop. The MAX5941A provides
internal slope compensation.
IEEE 802.3af-Compliant Power-Over-Ethernet
Interface/PWM Controller for Power Devices
14
RCL
______________________________________________________________________________________
will be 13V. If the maximum classification current
Thermal Dissipation
Current-Mode Control
PWM Controller
Isolated voltage feedback is achieved by using an opto-
coupler and a shunt regulator as shown in Figure 5. The
output voltage set-point accuracy is a function of the
accuracy of the shunt regulator and feedback resistor-
divider tolerance.
The internal regulators of the MAX5941A/MAX5941B
enable initial startup without a lossy startup resistor and
regulate the voltage at the output of a tertiary (bias) wind-
ing to provide power for the IC. At startup, V+ is regulat-
ed down to V
regulator then regulates from the output of the tertiary
winding to V
ing to have only a small filter capacitor at its output thus
eliminating the additional cost of a filter inductor.
When designing the tertiary winding, calculate the num-
ber of turns so the minimum reflected voltage is always
higher than 12.7V. The maximum reflected voltage must
be less than 36V.
To reduce power dissipation, the high-voltage regulator
is disabled when the V
greatly reduces power dissipation and improves effi-
ciency. If V
threshold (V
abled, and soft-start is reinitiated. In undervoltage lock-
out the MOSFET driver output (NDRV) is held low.
If the input voltage range is between 13V and 36V, V+
and V
that the maximum power dissipation is not exceeded.
This eliminates the need for a tertiary winding.
The soft-start feature of the MAX5941A/MAX5941B
allows the load voltage to ramp up in a controlled man-
ner, thus eliminating output voltage overshoot.
While the controller is in undervoltage lockout, the
capacitor connected to the SS_SHDN pin is dis-
charged. Upon coming out of undervoltage lockout, an
internal current source starts charging the capacitor to
initiate the soft-start cycle. Use the following equation to
calculate total soft-start time:
where C
Operation begins when V
When soft-start has completed, V
PWM Controller Undervoltage Lockout,
DD
SS
may be connected to the line voltage provided
is the soft-start capacitor as shown in Figure 5.
CC
CC
CC
CC
. This architecture allows the tertiary wind-
t
= 6.6V), the low-voltage regulator is dis-
startup
falls below the undervoltage lockout
to provide bias for the device. The V
=
Soft-Start, and Shutdown
DD
0 45
.
Optocoupled Feedback
SS_SHDN
voltage reaches 12.7V. This
ms
nF
Internal Regulators
×
SS_SHDN
C
ss
ramps above 0.6V.
is regulated
DD