MAX14575CETA+T Maxim Integrated, MAX14575CETA+T Datasheet
MAX14575CETA+T
Specifications of MAX14575CETA+T
Related parts for MAX14575CETA+T
MAX14575CETA+T Summary of contents
Page 1
... TDFN pack- age and operate over the -40NC to +85NC extended temperature range. PART PIN-PACKAGE MAX14575AETA+T 8 TDFN-EP* 8 TDFN-EP* MAX14575ALETA+T MAX14575BETA+T 8 TDFN-EP* MAX14575CETA+T 8 TDFN-EP* +Denotes a lead(Pb)-free/RoHS-compliant package Tape and reel. *EP = Exposed pad. POWER SUPPLY 1µF V PULLUP µP ...
Page 2
... C IN MIN TYP 2 130 6 = 5.5V, IN 0.1 = 0V, IN 0.07 = 100mA, OUT 32 2250 2500 450 500 200 250 135 1. 172 215 IN OUT 25 100 345 = 3.3V 1FF 1FF, IN OUT MAX UNITS 5.5 V 275 3 2750 550 mA 300 kV kI 258 145 mV mV Maxim Integrated ...
Page 3
... Note 3: Blanking time and retry time are generated by the same internal oscillator. The ratio of EN(EN)* V OUT *() THE POLARITY OF THE SIGNAL IS REVERSED FOR THE MAX14575AL ONLY. Figure 1. Timing Diagram for Measuring Turn-On Time (t Maxim Integrated MAX14575A/MAX14575AL/ MAX14575B/MAX14575C SYMBOL CONDITIONS I EN GND ...
Page 4
... CURRENT LIMIT LOAD CURRENT FLAG Figure 2. Autoretry Fault Diagram THE DEVICE GOES TO THERMAL-SHUTDOWN MODE Figure 3. Latchoff Fault Diagram BLANK RETRY BLANK RETRY t BLANK OUT CURRENT LIMIT LOAD CURRENT FLAG t t BLANK BLANK THE DEVICE GOES TO THERMAL-SHUTDOWN MODE t BLANK Maxim Integrated ...
Page 5
... TEMPERATURE (°C) SHUTDOWN REVERSE CURRENT vs. TEMPERATURE 1 0 5.5V OUT V = 2.3V 0.8 IN 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -40 - TEMPERATURE (°C) Maxim Integrated MAX14575A/MAX14575AL/ MAX14575B/MAX14575C Typical Operating Characteristics = 94.2kI +25NC, unless otherwise noted.) SETI A NORMALIZED CURRENT LIMIT vs. TEMPERATURE 1.3 1.2 1.1 1.0 0.9 0.8 0.7 5.5 -40 - TEMPERATURE (°C) SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE 1 ...
Page 6
... NO OUTPUT CAPACITOR + 3. -40 - TEMPERATURE (°C) CURRENT-LIMIT RESPONSE MAX14575A toc13 20ms/div SHORT TO GROUND APPLIED +3. FLAG 2V/div I OUT 1A/div 200mA OUT TO SHORT APPLIED +3. OUT 2V/div I OUT 1A/div Maxim Integrated ...
Page 7
... Adjustable Current-Limit Switches PIN MAX14575AL MAX14575_ — — — — Maxim Integrated MAX14575A/MAX14575AL/ MAX14575B/MAX14575C TOP VIEW GND EN(EN)** MAX14575A MAX14575AL MAX14575B MAX14575C EP FLAG SETI OUT TDFN (2mm × 2mm) *CONNECT EXPOSED PAD TO GND ...
Page 8
... Functional Diagram OUT FLAG SETI ) has elapsed. A retry BLANK ) starts immediately after the blanking , the switch turns on again. If the RETRY , when the switch is RETRY t BLANK × I LIM + t t BLANK RETRY = 15ms and t = 500ms, the RETRY Maxim Integrated BLANK ...
Page 9
... Table 1. Switch Truth Table MAX14575A/B/C MAX14575AL Maxim Integrated MAX14575A/MAX14575AL/ MAX14575B/MAX14575C • The reverse current protection has tripped • The die temperature exceeds +160NC • SETI is connected to ground has elapsed. The switch Thermal shutdown circuitry protects the devices from overheating. The switch turns off and FLAG goes low immediately when the junction temperature exceeds +160NC (typ) ...
Page 10
... Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE EP 8 TDFN-EP ~100I* Layout and Thermal Dissipation V × I IN(MAX) OUT(MAX (MAX RETRY BLANK Chip Information Package Information PACKAGE OUTLINE TYPE CODE NO. T822+2 21-0168 × t BLANK LAND PATTERN NO. 90-0065 Maxim Integrated ...
Page 11
... Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 2012 Maxim Integrated Products, Inc. © MAX14575A/MAX14575AL/ MAX14575B/MAX14575C DESCRIPTION Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. Revision History PAGES CHANGED — 11 ...