MAX3243EEAI-G071 Maxim Integrated, MAX3243EEAI-G071 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MAX3243EEAI-G071
Manufacturer Part Number
MAX3243EEAI-G071
Description
RS-232 Interface IC
Manufacturer
Maxim Integrated
Series
MAX3221E, MAX3223E, MAX3243Er
Datasheet
1.MAX3223EETP.pdf
(19 pages)
Specifications of MAX3243EEAI-G071
Data Rate
120 Kbps
Operating Supply Voltage
3 V to 5.5 V
Supply Current
1 mA
Operating Temperature Range
0 C to + 70 C
Mounting Style
SMD/SMT
Function
Transceiver
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Number Of Drivers
3
Number Of I/os
16
Number Of Receivers
5
Propagation Delay Time Ns
0.3 us
Shutdown
Yes
±15kV ESD-Protected, 1µA, 3.0V to 5.5V, 250kbps,
RS-232 Transceivers with AutoShutdown
The MAX3221E/MAX3223E/MAX3243E’s receivers con-
vert RS-232 signals to CMOS-logic output levels. All
receivers have inverting three-state outputs and can be
active or inactive. In shutdown (FORCEOFF = low) or in
AutoShutdown, the MAX3221E/MAX3223E’s receivers
are active (Table 1). Drive EN high to place the receiv-
er(s) in a high-impedance state. The MAX3243E’s
receivers are high-impedance when the part is in shut-
down (FORCEOFF = low).
The MAX3243E features an extra, always-active com-
plementary output (R2OUTB). R2OUTB monitors
receiver activity while the other receivers are high-
impedance. This allows Ring Indicator to be monitored
without forward biasing other devices connected to the
receiver outputs. This is ideal for systems where V
drops to 0 in shutdown to accommodate peripherals
such as UARTs (Figure 2).
The MAX3221E/MAX3223E/MAX3243E feature an
INVALID output that is enabled low when no valid RS-232
signal levels have been detected on all receiver inputs.
INVALID is functional in any mode (Figures 3 and 5).
The MAX3221E/MAX3223E/MAX3243E achieve a 1µA
supply current with Maxim’s new AutoShutdown fea-
ture, which operates when FORCEON is low and
FORCEOFF is high. When these devices sense no valid
signal levels on all receiver inputs for 30µs, the on-
board charge pump and drivers are shut off, reducing
supply current to 1µA. This occurs if the RS-232 cable
is disconnected or the connected peripheral transmit-
ters are turned off. The device turns on again when a
valid level is applied to any RS-232 receiver input. As a
result, the system saves power without changes to the
existing BIOS or operating system.
Table 2 and Figure 3c summarize the MAX3221E/
MAX3223E/MAX3243E operating modes. FORCEON
and FORCEOFF override AutoShutdown. When neither
control is asserted, the IC selects between these states
automatically, based on receiver input levels. Figures
3a, 3b, and 5a depict valid and invalid RS-232 receiver
levels. Figure 5 shows the input levels and timing dia-
gram for AutoShutdown operation.
MAX3221E/MAX3223E/MAX3243E
8
RS-232 Receivers
AutoShutdown
CC
Figure 2. The MAX3243E detects RS-232 activity when the
UART and interface are shut down.
a)
b)
OLDER RS-232: POWERED-DOWN UART DRAWS CURRENT FROM ACTIVE
RECEIVER OUTPUT IN SHUTDOWN.
NEW MAX3243E: IN SHUTDOWN, R2OUTB IS USED TO MONITOR EXTERNAL
V
V
DEVICES AND R2OUT IS THREE STATED, ELIMINATING A CURRENT PATH
THROUGH THE UART'S PROTECTION DIODE.
CC
CC
GND
UART
GND
UART
TO
µP
PROTECTION
DIODE
PROTECTION
DIODE
Rx
Rx
Tx
Tx
TRANSITION
DETECTOR
LOGIC
SHDN = GND
FORCEOFF = GND
THREE-STATED
V
CC
I
V
R2OUTB
CC
R2OUT
T1IN
I
MAX3243E
PREVIOUS
RS-232
5kΩ
Maxim Integrated
5kΩ
R2IN
T1OUT