CAT1163WI-25-G ON Semiconductor, CAT1163WI-25-G Datasheet - Page 8

no-image

CAT1163WI-25-G

Manufacturer Part Number
CAT1163WI-25-G
Description
Supervisory Circuits CPU w/16K
Manufacturer
ON Semiconductor
Datasheet

Specifications of CAT1163WI-25-G

Product Category
Supervisory Circuits
Rohs
yes
Number Of Voltages Monitored
1
Monitored Voltage
3 V, 3.3 V, 5 V
Undervoltage Threshold
2.55 V
Overvoltage Threshold
2.7 V
Output Type
Active High, Active Low, Open Drain
Manual Reset
Resettable
Watchdog
Watchdog
Battery Backup Switching
No Backup
Power-up Reset Delay (typ)
270 ms
Supply Voltage - Max
6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOIC-8 Wide
Chip Enable Signals
No
Maximum Power Dissipation
1000 mW
Minimum Operating Temperature
- 40 C
Power Fail Detection
No
Supply Current (typ)
3000 uA
Supply Voltage - Min
2.7 V
Byte Write
START condition and the slave address information (with
the R/W bit set to zero) to the Slave device. After the Slave
generates an acknowledge, the Master sends a 8−bit address
that is to be written into the address pointers of the CAT1163.
After receiving another acknowledge from the Slave, the
Master device transmits the data to be written into the
addressed memory location. The CAT1163 acknowledges
once more and the Master generates the STOP condition. At
this time, the device begins an internal programming cycle
to non−volatile memory. While the cycle is in progress, the
device will not respond to any request from the Master
device.
Acknowledge Polling
the typical write cycle time. Once the stop condition is issued
to indicate the end of the host’s write operation, the
CAT1163 initiates the internal write cycle. ACK polling can
be initiated immediately. This involves issuing the start
against inadvertent memory array programming. If the WP
pin is tied to V
becomes read only. The CAT1163 will accept both slave and
In the Byte Write mode, the Master device sends the
Disabling of the inputs can be used to take advantage of
The Write Protection feature allows the user to protect
BUS ACTIVITY:
SDA LINE
MASTER
CC
, the entire memory array is protected and
S
BUS ACTIVITY:
S
T
A
R
T
SDA LINE
ADDRESS
MASTER
SLAVE
S
S
A
R
T
T
C
A
K
ADDRESS (n)
ADDRESS
Figure 8. Page Write Timing
Figure 7. Byte Write Timing
SLAVE
WRITE OPERATIONS
WRITE PROTECTION
BYTE
http://onsemi.com
C
A
K
A
C
K
8
ADDRESS
Page Write
write cycle, using the Page Write operation. The page write
operation is initiated in the same manner as the byte write
operation, however instead of terminating after the initial
byte is transmitted, the Master is allowed to send up to 15
additional bytes. After each byte has been transmitted, the
CAT1163 will respond with an acknowledge and internally
increment the lower order address bits by one. The high
order bits remain unchanged.
the STOP condition, the address counter ‘wraps around,’
and previously transmitted data will be overwritten.
has been sent by the Master, the internal programming cycle
begins. At this point, all received data is written to the
CAT1163 in a single write cycle.
condition followed by the slave address for a write
operation. If the CAT1163 is still busy with the write
operation, no ACK will be returned. If a write operation has
completed, an ACK will be returned and the host can then
proceed with the next read or write operation.
byte addresses, but the memory location accessed is
protected from programming by the device’s failure to send
an acknowledge after the first byte of data is received.
BYTE
DATA n
The CAT1163 writes up to 16 bytes of data in a single
If the Master transmits more than 16 bytes before sending
When all 16 bytes are received, and the STOP condition
A
C
K
A
C
K
DATA n+1
DATA
C
A
K
A
C
K
P
O
S
T
P
DATA n+15
A
C
K
O
S
T
P
P

Related parts for CAT1163WI-25-G