CAT809HTBI-GT3 ON Semiconductor, CAT809HTBI-GT3 Datasheet
CAT809HTBI-GT3
Specifications of CAT809HTBI-GT3
Available stocks
Related parts for CAT809HTBI-GT3
CAT809HTBI-GT3 Summary of contents
Page 1
... The underlying floating gate technology, Analog EEPROM used by ON Semiconductor, makes it possible to offer any custom reset threshold value. Seven industry standard threshold levels are offered to support +5.0 V, +3.3 V, +3.0 V and +2.5 V systems. ...
Page 2
Table 1. THRESHOLD SUFFIX SELECTOR Nominal Threshold Voltage 4.63 V 4.55 V 4.38 V 4.00 V 3.08 V 2.93 V 2.63 V 2.32 V 1.60 V Table 2. PIN DESCRIPTIONS Pin Number CAT803 CAT809 CAT810 ...
Page 3
TOLERANCE CC BIAS – VOLTAGE REFERENCE GND TOLERANCE CC BIAS – VOLTAGE REFERENCE GND TOLERANCE CC BIAS – VOLTAGE REFERENCE GND Figure 1. Block Diagrams http://onsemi.com 3 V ...
Page 4
Table 4. ELECTRICAL CHARACTERISTICS (V = Full range −40°C to +85°C, unless otherwise specified. Typical values versions 3.3 V for the T/S versions Symbol Parameter V Range CC I Supply ...
Page 5
TYPICAL OPERATING CHARACTERISTICS (V = Full range −40°C to +85°C, unless otherwise specified. Typical values L/M/J versions 3.3 V for the T/S versions 260 240 ...
Page 6
Detailed Descriptions Reset Timing The reset signal is asserted LOW for the CAT803/CAT809 and HIGH for the CAT810 when the power supply voltage falls below the threshold trip voltage and remains asserted for at least 140 ms after the power ...
Page 7
Valid RESET with V Under 1 ensure that the CAT809 RESET pin known state when V RESET pin and GND is recommended. For the CAT810, a pull−up resistor from RESET pin to V Power ...
Page 8
... CAT809TSDI−T3 CAT809SSDI−GT3 CAT809SSDI−T3 CAT809RSDI−GT3 CAT809RSDI−T3 CAT809ZSDI−GT3 CAT809ZSDI−T3 CAT809LTBI−GT3 CAT809LTBI−T3 CAT809HTBI−GT3 CAT809HTBI−T3 CAT809MTBI−GT3 CAT809MTBI−T3 CAT809JTBI−GT3 CAT809JTBI−T3 CAT809TTBI−GT3 CAT809TTBI−T3 CAT809STBI−GT3 CAT809STBI−T3 CAT809RTBI−GT3 CAT809RTBI−T3 CAT809ZTBI− ...
Page 9
... For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 6. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device Nomenclature document, TND310/D, available at www.onsemi.com ...
Page 10
TOP VIEW b A1 SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC TO-236. PACKAGE DIMENSIONS SOT−23, 3 Lead CASE 527AG−01 ISSUE O SYMBOL A A1 ...
Page 11
... Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303− ...