M25P10-AVMP6TG NUMONYX, M25P10-AVMP6TG Datasheet - Page 20
![IC FLASH 1MBIT 50MHZ 8VFQFPN](/photos/7/23/72354/m25p10-avmp6t_sml.jpg)
M25P10-AVMP6TG
Manufacturer Part Number
M25P10-AVMP6TG
Description
IC FLASH 1MBIT 50MHZ 8VFQFPN
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P10-AVMP6TG.pdf
(51 pages)
Specifications of M25P10-AVMP6TG
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
1M (128K x 8)
Speed
50MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-VFQFN, 8-VFQFPN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P10-AVMP6TG
M25P10-AVMP6TGTR
M25P10-AVMP6TGTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P10-AVMP6TG
Manufacturer:
Micron Technology Inc
Quantity:
10 000
6.4
6.4.1
6.4.2
6.4.3
6.4.4
20/51
Read Status Register (RDSR)
The Read Status Register (RDSR) instruction allows the Status Register to be read. The
Status Register may be read at any time, even while a Program, Erase or Write Status
Register cycle is in progress. When one of these cycles is in progress, it is recommended to
check the Write In Progress (WIP) bit before sending a new instruction to the device. It is
also possible to read the Status Register continuously, as shown in
Table 6.
The status and control bits of the Status Register are as follows:
WIP bit
The Write In Progress (WIP) bit indicates whether the memory is busy with a Write Status
Register, Program or Erase cycle. When set to ‘1’, such a cycle is in progress, when reset to
‘0’ no such cycle is in progress.
WEL bit
The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch.
When set to ‘1’ the internal Write Enable Latch is set, when set to ‘0’ the internal Write
Enable Latch is reset and no Write Status Register, Program or Erase instruction is
accepted.
BP1, BP0 bits
The Block Protect (BP1, BP0) bits are non-volatile. They define the size of the area to be
software protected against program and erase instructions. These bits are written with the
Write Status Register (WRSR) instruction. When one or both of the Block Protect (BP1,
BP0) bits is set to ‘1’, the relevant memory area (as defined in
against Page Program (PP) and Sector Erase (SE) instructions. The Block Protect (BP1,
BP0) bits can be written provided that the Hardware Protected mode has not been set. The
Bulk Erase (BE) instruction is executed if, and only if, both Block Protect (BP1, BP0) bits are
0.
SRWD bit
The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write
Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W)
signal allow the device to be put in the Hardware Protected mode (when the Status Register
Write Disable (SRWD) bit is set to ‘1’, and Write Protect (W) is driven Low). In this mode, the
Status Register Write Protect
SRWD
b7
Status Register format
0
0
0
BP1
Block Protect bits
Write Enable Latch bit
BP0
Table
Figure
2) becomes protected
WEL
Write In Progress bit
10.
WIP
b0