M27C4001-10F1 STMicroelectronics, M27C4001-10F1 Datasheet - Page 9

• Manufacturer Part Number: M27C4001-10F1
• Description: IC EPROM 4MBIT 100NS 32CDIP
• Manufacturer: STMicroelectronics

Specifications of M27C4001-10F1

• Format - Memory: EPROMs
• Memory Type: UV EPROM
• Memory Size: 4M (512K x 8)
• Speed: 100ns
• Interface: Parallel
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-CDIP (0.600", 15.24mm) Window
• Capacitance, Input: 6 pF
• Capacitance, Output: 12 pF
• Current, Input, Leakage: ±10 μA (Read)
• Current, Operating: 30 mA (Read)
• Current, Output, Leakage: ±10 μA (Read)
• Current, Supply: 30 mA
• Density: 4M
• Organization: 512K×8
• Package Type: FDIP32W
• Temperature, Operating: 0 to +70 °C
• Temperature, Operating, Maximum: 70 °C
• Temperature, Operating, Minimum: 0 °C
• Time, Access: 100 ns
• Time, Fall: ≤20 ns
• Time, Programmable: 100 μs
• Time, Rise: ≤20 ns
• Voltage, Input, High: 6 V (Read)
• Voltage, Input, High Level: 2 V (Min.)
• Voltage, Input, Low: 0.8 V (Read)
• Voltage, Input, Low Level: -0.3 V (Max.)
• Voltage, Output, High: 4.3 V (Read)
• Voltage, Output, Low: 0.4 V (Read)
• Voltage, Programmable: 11.5 V (Min.)
• Voltage, Supply: 5 V
• Access Time: 35ns
• Supply Voltage Range: 4.5V To 5V
• No. Of Pins: 32
• Operating Temperature Range: 0°C To +70°C
• Voltage, Vcc: 5V
• Ic Interface Type: Parallel
• Programming Voltage: 12.75V
• Rohs Compliant: Yes
• Memory Configuration: 512K X 8
• Memory Case Style: FDIPW
• Supply Voltage Max: 5V
• Operating Temperature Max: 70°C
• Operating Temperature Min: 0°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-1658-5

M27C4001
2.4
2.5
2.6
System Considerations
The power switching characteristics of Advanced CMOS EPROMs require careful
decoupling of the devices. The supply current, I
the system designer: the standby current level, the active current level, and transient current
peaks that are produced by the falling and rising edges of E. The magnitude of the transient
current peaks is dependent on the capacitive and inductive loading of the device at the
output. The associated transient voltage peaks can be suppressed by complying with the
two line output control and by properly selected decoupling capacitors. It is recommended
that a 0.1 F ceramic capacitor be used on every device between V
be a high frequency capacitor of low inherent inductance and should be placed as close to
the device as possible. In addition, a 4.7 F bulk electrolytic capacitor should be used
between V
power supply connection point. The purpose of the bulk capacitor is to overcome the voltage
drop caused by the inductive effects of PCB traces.
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27C4001 are in the
'1' state. Data is introduced by selectively programming '0's into the desired bit locations.
Although only '0's will be programmed, both '1's and '0's can be present in the data word.
The only way to change a '0' to a '1' is by die exposure to ultraviolet light (UV EPROM). The
M27C4001 is in the programming mode when V
pulsed to V
pins. The levels required for the address and data inputs are TTL. V
6.25V ± 0.25V.
PRESTO II Programming Algorithm
PRESTO II Programming Algorithm allows the whole array to be programmed with a
guaranteed margin, in a typical time of 52.5 seconds. Programming with PRESTO II
consists of applying a sequence of 100 s program pulses to each byte until a correct verify
occurs (see
automatically activated in order to guarantee that each cell is programmed with enough
margin. No overprogram pulse is applied since the verify in MARGIN MODE provides the
necessary margin to each programmed cell.
CC
IL
Figure
. The data to be programmed is applied to 8 bits in parallel to the data output
and V
5). During programming and verify operation, a MARGIN MODE circuit is
SS
for every eight devices. The bulk capacitor should be located near the
CC
PP
, has three segments that are of interest to
input is at 12.75V, G is at V
CC
CC
and V
is specified to be
Device operation
SS
. This should
IH
and E is
9/25