MAX705EUA-T Maxim Integrated, MAX705EUA-T Datasheet
MAX705EUA-T
Specifications of MAX705EUA-T
Related parts for MAX705EUA-T
MAX705EUA-T Summary of contents
Page 1
... MAX706/MAX708 generate a reset pulse below 4.40V. All four parts are available in 8-pin DIP, SO and µMAX packages. _______________________Applications Computers Controllers Intelligent Instruments Automotive Systems Critical µP Power Monitoring µMAX is a registered trademark of Maxim Integrated Products, Inc. __________Typical Operating Circuit UNREGULATED DC MAX667 +5V DC LINEAR REGULATOR V RESET CC ...
Page 2
... MIN MAX MIN TYP MAX 1.0 1.1 1.2 150 150 50 50 4.50 4.65 4.75 4.25 4.40 4.50 40 140 200 50µA = 100µA SINK = 800µ 1 1.1V 0 1.2V 0 800µ 1 3.2mA 1.00 1.60 2. -150 - 1.5 CC UNITS 5.5 5.5 V 5.5 350 500 µA 350 500 V mV 280 ms 0.4 V 0.3 0.3 0 0.8 V 150 µA V 0.4 Maxim Integrated ...
Page 3
... MR Input Threshold High MR to Reset Out Delay (Note 2) PFI Input Threshold PFI Input Current PFO Output Voltage Note 2: Applies to both RESET in the MAX705–MAX708 and RESET in the MAX707/MAX708/MAX813L. Maxim Integrated MAX705–MAX708/MAX813L Low-Cost, µP Supervisory Circuits = 4.5V to 5.5V for MAX706/MAX708 SYMBOL CONDITIONS ...
Page 4
... +25° RESET 10kΩ 0V RESET RESET 10kΩ GND 330pF +5V RESET 330pF 0V 400ns/div MAX813L RESET RESPONSE TIME + RESET 330pF 10kΩ GND +4V 2µs/div +25°C A 1kΩ +3V +1.30V RESET 330pF RESET Maxim Integrated ...
Page 5
... Maxim Integrated MAX705–MAX708/MAX813L Low-Cost, µP Supervisory Circuits MAX813L NAME DIP/SO µMAX GND 4 6 PFI PFO WDI — ...
Page 6
... MR can be used to force a watch- dog timeout to generate a reset pulse in the MAX705/ MAX706/MAX813L. Simply connect WDO to MR 250µA 1 RESET 2 GENERATOR MAX707 4.65V* MAX708 4 1.25V GND RESET 7 RESET 5 PFO drops below CC falls below the Manual Reset Maxim Integrated ...
Page 7
... MR EXTERNALLY DRIVEN LOW Figure 4. MAX705/MAX706 RESET, MR, and WDO Timing with WDI Three-Stated. The MAX707/MAX708/MAX813L RESET output is the inverse of RESET shown. Maxim Integrated MAX705–MAX708/MAX813L Low-Cost, µP Supervisory Circuits To build an early-warning circuit for power failure, con- nect the PFI pin to a voltage divider (see Typical Operating Circuit ) ...
Page 8
... CC 1MΩ 1% MAX70_ MR 130kΩ PFI PFO 1% GND PARAMETER MIN TYP MAX +12V Reset 10.67 10.87 11.50 Threshold at +25°C BUFFERED RESET TO OTHER SYSTEM COMPONENTS V CC MAX70_ 4.7kΩ RESET RESET GND Interfacing to µPs with Bidirectional Reset Pins TO µP UNIT µP GND Maxim Integrated ...
Page 9
... Information (continued) PART TEMP RANGE MAX705EPA -40°C to +85°C MAX705ESA -40°C to +85°C MAX705EUA -40°C to +85°C MAX705MJA -55°C to +125°C MAX706CPA 0°C to +70°C MAX706CSA 0°C to +70°C MAX706CUA 0°C to +70°C MAX706C/D 0°C to +70°C MAX706EPA -40°C to +85°C MAX706ESA -40° ...
Page 10
... Max Resistance On OUT CC -to-V V Switch Backup-Battery Output Watchdog Separate Available if (sec), Period Timeout Watchdog Nominal Valid – — — — — – Reset Active-High Reset Active-Low (ms) Width Pulse Reset Minimum (V) Threshold Reset Nominal Number Part 10 Maxim Integrated ...
Page 11
... RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE 8 µMAX 8 Plastic DIP 8 SO Maxim Integrated MAX705–MAX708/MAX813L Low-Cost, µP Supervisory Circuits PACKAGE CODE U8-1 P8-1 ...
Page 12
... Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed ...