25AA010A-I/MS Microchip Technology, 25AA010A-I/MS Datasheet
25AA010A-I/MS
Specifications of 25AA010A-I/MS
Available stocks
Related parts for 25AA010A-I/MS
25AA010A-I/MS Summary of contents
Page 1
... TSSOP, 8-lead 2x3 DFN, and 6-lead SOT-23. Package Types (not to scale) TSSOP/MSOP (ST, MS SOT-23 (OT SCK HOLD *25XX010A is used in this document as a generic part number for the 25AA010A and the 25LC010A. Preliminary Packages P, MS, SN, ST, MC MS, SN, ST, MC, OT PDIP/SOIC (P, SN HOLD 7 7 HOLD HOLD 6 6 SCK SCK SCK 5 5 ...
Page 2
... ELECTRICAL CHARACTERISTICS (†) Absolute Maximum Ratings V .............................................................................................................................................................................6.5V CC All inputs and outputs w.r.t. V ......................................................................................................... -0. Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias ...............................................................................................................-40°C to 125°C ESD protection on all pins ..........................................................................................................................................4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device ...
Page 3
... Total Endurance™ Model which can be obtained from our web site: www.microchip.com begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle WC is complete. © 2006 Microchip Technology Inc. 25AA010A/25LC010A Industrial (I -40°C to +85°C A Automotive (E -40° ...
Page 4
... TABLE 1-2: AC CHARACTERISTICS (CONTINUED) AC CHARACTERISTICS Param. Sym. Characteristic No HOLD Hold Time HOLD Low to Output HZ High HOLD High to Output HV Valid 20 T Internal Write Cycle Time WC (byte or page) 21 — Endurance Note 1: This parameter is periodically sampled and not 100% tested. 2: This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ ...
Page 5
... SI HOLD FIGURE 1-2: SERIAL INPUT TIMING CS 2 Mode 1,1 SCK Mode 0 MSB in SO FIGURE 1-3: SERIAL OUTPUT TIMING SCK 13 MSB out SO SI © 2006 Microchip Technology Inc. 25AA010A/25LC010A high-impedance n don’t care high-impedance 14 don’t care Preliminary LSB in 3 Mode 1,1 ...
Page 6
... FUNCTIONAL DESCRIPTION 2.1 Principles of Operation The 25XX010A is a 128 byte Serial EEPROM designed to interface directly with the Serial Peripheral Interface (SPI) port of many of today’s popular microcontroller families, including Microchip’s PICmicro lers. It may also interface with microcontrollers that do ...
Page 7
... SI high-impedance SO © 2006 Microchip Technology Inc. 25AA010A/25LC010A HV Generator EEPROM Array Page Latches Y Decoder Sense Amp. R/W Control Read data from memory array beginning at selected address Write data to memory array beginning at selected address Reset the write enable latch (disable write operations) Set the write enable latch (enable write operations) ...
Page 8
... FIGURE 2-2: BYTE WRITE SEQUENCE SCK Instruction don’t care FIGURE 2-3: PAGE WRITE SEQUENCE SCK Instruction SCK data byte don’t care DS21832C-page Address byte high-impedance Address byte data byte Preliminary Twc data byte data byte data byte n (16 max) ...
Page 9
... FIGURE 2-5: WRITE DISABLE SEQUENCE (WRDI) CS SCK SI SO © 2006 Microchip Technology Inc. 25AA010A/25LC010A The following is a list of conditions under which the write enable latch will be reset: • Power-up See • WRDI instruction successfully executed • WRSR instruction successfully executed • WRITE instruction successfully executed • ...
Page 10
... Read Status Register Instruction (RDSR) The Read Status Register instruction (RDSR) provides access to the STATUS register. See Figure 2-6 for the RDSR timing sequence. The STATUS register may be read at any time, even during a write cycle. The STA- TUS register is formatted as follows: ...
Page 11
... Table 2-3. FIGURE 2-7: WRITE STATUS REGISTER TIMING SEQUENCE (WRSR SCK instruction Note: An internal write cycle (T WC sequence. © 2006 Microchip Technology Inc. 25AA010A/25LC010A TABLE 2-3: BP1 data to STATUS register ...
Page 12
... Data Protection The following protection has been implemented to prevent inadvertent writes to the array: • The write enable latch is reset on power-up • A write enable instruction must be issued to set the write enable latch • After a byte write, page write or STATUS register write, the write enable latch is reset • ...
Page 13
... The SI pin is used to transfer data into the device. It receives instructions, addresses and data. Data is latched on the rising edge of the serial clock. © 2006 Microchip Technology Inc. 25AA010A/25LC010A 3.5 Serial Clock (SCK) The SCK is used to synchronize the communication between a master and the 25XX010A. Instructions, ...
Page 14
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21832C-page 14 Example: 25AA010A e 3 I/P 1L7 0627 Example: ...
Page 15
... Package Marking Information (continued) 8-Lead 2X3 DFN XXX YWW NN 6-Lead SOT-23 XXNN © 2006 Microchip Technology Inc. 25AA010A/25LC010A Example: 401 627 L7 Example: 12L7 Preliminary DS21832C-page 15 ...
Page 16
... Plastic Dual In-line (P) – 300 mil (PDIP Units Dimension Limits n Number of Pins p Pitch Top to Seating Plane A Molded Package Thickness A2 Base to Seating Plane A1 Shoulder to Shoulder Width E Molded Package Width E1 Overall Length D Tip to Seating Plane L c Lead Thickness Upper Lead Width ...
Page 17
... Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057 © 2006 Microchip Technology Inc. 25AA010A/25LC010A Units ...
Page 18
... Plastic Thin Shrink Small Outline (ST) – 4.4 mm (TSSOP Dimension Limits Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Molded Package Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top ...
Page 19
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. BSC: Basic Dimension. Theoretically exact value shown without tolerances. See ASME Y14.5M REF: Reference Dimension, usually without tolerance, for information purposes only. See ASME Y14.5M JEDEC Equivalent: MO-187 Drawing No. C04-111 © 2006 Microchip Technology Inc. 25AA010A/25LC010A INCHES ...
Page 20
... Plastic Dual-Flat, No-Lead Package (MC) 2x3x0.9 mm Body (DFN) – Saw Singulated D PIN 1 ID INDEX AREA (NOTE 1) TOP VIEW A3 Dimension Limits Number of Pins Pitch Overall Height Standoff Contact Thickness Overall Length Overall Width Exposed Pad Length Exposed Pad Width Contact Length § ...
Page 21
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. BSC: Basic Dimension. Theoretically exact value shown without tolerances. See ASME Y14.5M JEITA (formerly EIAJ) equivalent: SC-74A Drawing No. C04-120 © 2006 Microchip Technology Inc. 25AA010A/25LC010A ...
Page 22
... APPENDIX A: REVISION HISTORY Revision B Corrections to Section 1.0, Electrical Characteristics. Revision C Added Packages SOT-23, DFN and X-rotated TSSOP; Revised AC Char., Params. 9, 10; Revised Package Legend. DS21832C-page 22 Preliminary © 2006 Microchip Technology Inc. ...
Page 23
... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2006 Microchip Technology Inc. 25AA010A/25LC010A CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • Distributor or Representative • ...
Page 24
... Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y Device: 25AA010A/25LC010A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs you find the organization of this document easy to follow? If not, why? 4 ...
Page 25
... Register on our web site (www.microchip.com/cn) to receive the most current information on our products. © 2006 Microchip Technology Inc. 25AA010A/25LC010A /XX Examples: Package a) 25AA010A-I/MS = 1k-bit, 16-byte page, 1.8V Serial EEPROM, Industrial temp., MSOP package b) 25AA010AT-I/SN = 1k-bit, 16-byte page, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, SOIC package c) 25LC010AT-I/SN = 1k-bit, 16-byte page, 2 ...
Page 26
... NOTES: DS21832C-page 24 Preliminary © 2006 Microchip Technology Inc. ...
Page 27
... PowerMate, PowerTool, Real ICE, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and Zena are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 28
... Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Preliminary © 2006 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...