AT25640B-SSHL-T Atmel, AT25640B-SSHL-T Datasheet - Page 9
![IC EEPROM 64KBIT 20MHZ 8SOIC](/photos/6/50/65032/453-8-soic_sml.jpg)
AT25640B-SSHL-T
Manufacturer Part Number
AT25640B-SSHL-T
Description
IC EEPROM 64KBIT 20MHZ 8SOIC
Manufacturer
Atmel
Datasheet
1.AT25320B-SSHL-B.pdf
(26 pages)
Specifications of AT25640B-SSHL-T
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
64K (8K x 8)
Speed
5MHz, 10MHz, 20MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Density
64Kb
Interface Type
Serial (SPI)
Organization
8Kx8
Access Time (max)
80ns
Frequency (max)
5MHz
Write Protection
Yes
Data Retention
100Year
Operating Supply Voltage (typ)
2.5/3.3/5V
Operating Temp Range
-40C to 85C
Supply Current
10mA
Operating Supply Voltage (min)
1.8V
Operating Supply Voltage (max)
5.5V
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT25640B-SSHL-T
Manufacturer:
ASTEC
Quantity:
12
Company:
Part Number:
AT25640B-SSHL-T
Manufacturer:
Atmel
Quantity:
61 380
Company:
Part Number:
AT25640B-SSHL-T
Manufacturer:
ATMEL
Quantity:
113
Part Number:
AT25640B-SSHL-T
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
8535F–SEEPR–6/10
WRITE SEQUENCE (WRITE): In order to program the Atmel
executed. First, the device must be write enabled via the WREN instruction. Then a write (WRITE) instruction
may be executed. Also, the address of the memory location(s) to be programmed must be outside the protected
address field location selected by the block write protection level. During an internal write cycle, all commands will
be ignored except the RDSR instruction.
A write instruction requires the following sequence. After the CS line is pulled low to select the device, the WRITE
op-code is transmitted via the SI line followed by the byte address (A15
grammed (see
CS pin must occur during the SCK low-time immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status register
(RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle has ended. Only the
RDSR instruction is enabled during the write programming cycle.
The AT25320B/640B is capable of a 32-byte page write operation. After each byte of data is received, the five low-
order address bits are internally incremented by one; the high-order bits of the address will remain constant. If
more than 32-bytes of data are transmitted, the address counter will roll over and the previously written data will be
overwritten. The AT25320B/640B is automatically returned to the write disable state at the completion of a write
cycle.
Note:
Table 3-6.
If the device is not write-enabled (WREN), the device will ignore the write instruction and will return to the standby
state, when CS is brought high. A new CS falling edge is required to reinitiate the serial communication.
Don’t Care Bits
Address
Address Key
A
Table
N
3-6). Programming will start after the CS pin is brought high. The low-to-high transition of the
Atmel AT25320B
A
A
15
11
–A
–A
12
0
®
AT25320B/640B, two separate instructions must be
Atmel AT25640B
Atmel AT25320B/640B
A
–
A
A0) and the data (D7
15
12
–A
–A
13
0
–
D0) to be pro-
9