MIKROE-1043 mikroElektronika, MIKROE-1043 Datasheet - Page 20

• Manufacturer Part Number: MIKROE-1043
• Description: Development Boards & Kits - ARM EasyMxPRO v7 MCU Stellaris LM4F232H5Q
• Manufacturer: mikroElektronika

Specifications of MIKROE-1043

• Rohs: yes
• Product: Development Boards
• Tool Is For Evaluation Of: LM4F232H5Q
• Core: ARM Cortex M3, ARM Cortex M4
• Interface Type: CAN, I2C, SPI
• Operating Supply Voltage: 7 V to 23 V
• Data Bus Width: 8 bit
• Dimensions: 266 mm x 220 mm
• For Use With: LM4F232H5Q

page 20
mikroBUS
Easier connectivity and simple configuration
are imperative in modern electronic devices.
Success of the USB standard comes from it’s
simplicity of usage and high and reliable data
transfer rates. As we in mikroElektronika see it,
Plug-and-Play devices with minimum settings
are the future in embedded world too. This is
why our engineers have come up with a simple,
but brilliant pinout with lines that most of
today’s accessory boards require, which almost
completely eliminates the need of additional
hardware settings. We called this new standard
the mikroBUS
supports mikroBUS
As you can see, there are no additional DIP
switches, or jumper selections. Everything is
™
. EasyMx PRO
™
with two on-board sockets.
™
v7 for Stellaris
®
already routed to the most appropriate pins of
the microcontroller sockets.
mikroBUS
Each mikroBUS
1x8 female headers containing pins that are
most likely to be used in the target accessory
board. There are three groups of communication
pins: SPI, UART and I
are also single pins for PWM, Interrupt,
Analog input, Reset and Chip Select. Pinout
contains two power groups: +5V and GND on
one header and +3.3V and GND on the other
1x8 header.
™
PD5
PE2
PG0
PA2
PA4
PA5
VCC-3.3V
sockets
™
™
host connector consists of two
AN
RST
CS
SCK
MISO
MOSI
3.3V
GND
host connector
1
2
C communication. There
PWM
GND
SDA
INT
SCL
RX
TX
5V
VCC-5V
PC4
PH0
PA0
PA1
PB2
PB3
Integrate mikroBUS
mikroBUS
freely place mikroBUS
clearly mark them with mikroBUS
information, logo artwork and PCB files visit our web site:
http://www.mikroe.com/mikrobus
™
is not made to be only a part of our development boards. You can
mikroBUS
AN
RST
CS
SCK
MISO
MOSI
+3.3V
GND
- SPI Chip Select line
- Analog pin
PD6
PE3
PG1
PA2
PA4
PA5
- Reset pin
- SPI Clock line
- Reference Ground
VCC-3.3V
- SPI Slave Output line
- SPI Slave Input line
™
- VCC-3.3V power line
host connectors in your final PCB designs, as long as you
AN
RST
CS
SCK
MISO
MOSI
3.3V
GND
™
™
in your design
™
pinout explained
2
logo and footprint specifications. For more
PWM
GND
SDA
INT
SCL
RX
TX
5V
VCC-5V
PC6
PH1
PD2
PD3
PB2
PB3
PWM
INT
RX
TX
SCL
SDA
+5V
GND
EasyMx PRO
- UART Transmit line
- UART Receive line
- Hardware Interrupt line
- I2C Clock line
- I2C Data line
- VCC-5V power line
- Reference Ground
- PWM output line
DATA BUS
Figure 7-1:
connection
mikroBUS
schematic
™
v7