MAX155EVKIT-DIP Maxim Integrated, MAX155EVKIT-DIP Datasheet - Page 2

• Manufacturer Part Number: MAX155EVKIT-DIP
• Description: Data Conversion IC Development Tools Evaluation Kit for the MAX155
• Manufacturer: Maxim Integrated
• Series: MAX155, MAX156r

MAX155 Evaluation Kit
2
C4, C5, C7, C8,
DESIGNATION
C11, C12, C13,
C14, C16, C17,
C18, C19, C20,
Connector 1
Connector 2
C3, C6, C9,
C10, C22
_______________________________________________________________________________________
R4–R11
C1, C2
J1, J2
RSIP1
None
None
None
IC10
IC11
IC12
IC13
IC14
XX1
C21
C15
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC9
R1
R2
R3
QTY
13
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
8
2
5
2
1
2
1
8.0in x 5.5in MAX155 EV kit
printed circuit board
MAX233ACPP
MAX696CPE
80C32
74HCT573
74HCT08
74HCT139
27C64
6264LP
74HCT245
MAX155BCPI
MAX660
74HCT161
10MHz OSC
MAX667CPA
CTS CTX078 11.059MHz crystal
2-pin header and shunts
2-wire power connector
D9 right-angle female connector
32.4k 1% resistor
13.0k 1% resistor
10k 5% resistor
1.0k 5% resistors
27pF capacitors
0.1µF 50V monolithic
capacitors
10µF 16V tantalum
capacitors
33µF 16V tantalum
capacitors
10-pin, 9-resistor 10k SIP
28-pin IC sockets for EPROM and
MAX155
MAX155 data sheet
Component List
DESCRIPTION
Setup and operation of the MAX155 EV kit involves the
following steps:
1. Assemble the printed circuit board using the proce-
2. Copy the MAX155 EV kit floppy disk to another disk
3. Read the README file for updates and changes.
4. Connect a cable between a serial port (COM1 or
5. Start the MAX155 EV software program on the
6. Apply power to the printed circuit board and make
7. Connect the input signals to the analog input(s) and
The following is an overview of the various circuits found
on the MAX155 EV kit printed circuit board. Refer to the
individual device data sheets for complete descriptions.
The MAX155 EV kit requires a 6V to 12V input supply. The
board typically draws 80mA of current; however, the input
supply should be capable of 150mA. The input supply
passes through D1 and is regulated to +5.0V by the
MAX667. The current available for additional user circuits
in the prototype area is limited by the capabilities of the
MAX667. Refer to the MAX667 data sheet for detailed
information before connecting loads greater than 20mA.
The MAX155 V
many applications. The -5V supply is necessary only
when the system requires inputs below ground (bipolar,
single-ended mode with ±2.5V input range). The EV kit
includes a MAX660 to generate the -5V needed to
enable this feature. Additional circuits can draw power
from this source as long as the load is no more than
10mA. For more current, the 10µF capacitors around
dure in the
and store the original in a safe place. Use the copy
for normal operation.
COM2) of the personal computer and the MAX155
EV kit printed circuit board. If a 9-pin (D9) connec-
tor is available, a straight-through cable can be
used. If the only available connector is a 25-pin
(D25) connector, an adapter is required.
personal computer and set the indicated active port
to agree with the cable location. The status line at
the bottom of the display shows the COM port and
board status.
sure the board status display in the lower right
corner indicates READY. If not, see the Trouble-
shooting Guide section.
the system is ready for operation.
Board Assembly section.
SS
pin can be connected to ground in
Detailed Description
Hardware Architecture
Quick Reference
Power Supply