UM232H-B-NC FTDI, UM232H-B-NC Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
UM232H-B-NC
Manufacturer Part Number
UM232H-B-NC
Description
Interface Development Tools USB to Serial/Paral. Break Out Board
Manufacturer
FTDI
Type
USB to Serial/Parallelr
Datasheet
1.UM232H-B-01.pdf
(14 pages)
Specifications of UM232H-B-NC
Rohs
yes
Product
Development Modules
Tool Is For Evaluation Of
FT232H
Interface Type
245 FIFO, FT1248, GPIO, I2C, SPI, UART, USB
Operating Supply Voltage
3.3 V
Dimensions
38.5 mm x 19.2 mm x 2 mm
Operating Supply Current
90 mA
For Use With
FT232H
8
Following a power-on reset or a USB reset the FT232H will scan its internal EEPROM and read the USB
configuration descriptors stored there. The default values programmed into the external EEPROM for the
FT232H used on the UM232H-B are shown in Table 8.1.
Parameter
USB Vendor ID (VID)
USB Product UD (PID)
Serial Number Enabled?
Serial Number
Pull down I/O Pins in USB
Suspend
Manufacturer Name
Product Description
Max Bus Power Current
Power Source
Device Type
USB Version
Remote Wake Up
High Current I/Os
Load VCP Driver
CBUS0
CBUS1
CBUS2
CBUS3
CBUS4
CBUS5
CBUS6
CBUS7
CBUS8
CBUS9
Invert UART
Table 8.1 – Default Internal MTP ROM Configuration
The on board EEPROM can be programmed over USB using the utility program FT_PROG. FT_PROG can
be downloaded from the www.ftdichip.com. Users who do not have their own USB vendor ID but who
would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs.
Contact
Internal MTP ROM Configuration
FTDI Support
(support1@ftdichip.com) for this service, also see
Bus Powered
UM232H-B
See Note
PWREN#
PWREN#
Disabled
Disabled
Disabled
TriSt-PU
TriSt-PU
TriSt-PU
TriSt-PU
TriSt-PU
TriSt-PU
TriSt-PU
TriSt-PU
Enabled
Enabled
FT232H
0403h
6014h
90mA
Value
0200
FTDI
Yes
Copyright © 2012 Future Technology Devices International Limited
Notes
FTDI default VID (hex)
FTDI default PID (hex)
A unique serial number is generated and programmed into
the EEPROM during final test of the UM232H-B module.
Enabling this option will make the device pull down on the
UART interface lines when the power is shut off (PWREN#
is high).
Returns USB 2.0 device description to the host. Note: The
device is a USB 2.0 Full Speed device (12Mb/s) as opposed
to a USB 2.0 High Speed device (480Mb/s).
Taking RI# low will wake up the USB host controller from
suspend.
Enables the high drive level on the UART and CBUS I/O
pins.
Makes the device load the CVP driver interface for the
device.
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Tristate Input pulled up
Power Enable, low when FT232H enumerates, switches 5V
output power on when the device enumerates.
Power Enable, low when the FT232H enumerates, ,
switches the on board LED on when the device enumerates.
Signal on this pin becomes TXD# if enable.
Document Reference No.: FT_000721
TN_100
UM232H-B Datasheet
and TN_101.
Clearance No.: FTDI#
10
Version 1.0
320