MAX1168EVKIT Maxim Integrated, MAX1168EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1168EVKIT
• Description: Data Conversion IC Development Tools MAX1168 Evaluation Kit/Evaluation System
• Manufacturer: Maxim Integrated
• Series: MAX1167, MAX1168r

Specifications of MAX1168EVKIT

• Interface Type: QSPI, Serial (SPI, Microwire)

MAX1168 Evaluation Kit/Evaluation System
Note: Indicate that you are using the MAX1168 when contact-
ing these component suppliers.
• MAX1168 EV system
• Three DC power supplies:
• 0 to 4.096V analog signal source
• A user-supplied Windows 2000/XP PC with an avail-
• USB cable (included with the USBTO232)
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit software. Text in bold and
underlined refers to items from the Windows
98/2000/XP operating system.
The MAX1168 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power until all connec-
tions are complete.
1) Visit the Maxim website (www.maxim-ic.com/evkit-
2
Fairchild
Semiconductor
TDK Corp.
HELPFILE.HTM
MAX1168.EXE
INSTALL.EXE
KIT1168.C16
able USB port
FILE NAME
SUPPLIER
Recommended Equipment—USB Port PC
UNINST.INI
_______________________________________________________________________________________
software) to download the latest version of the
USBTO232 user guide. Follow the steps in the
USBTO232 user guide Quick Start section and return
to step 2 of this Quick Start section when finished.
MAX1168 EV kit
68HC16MODULE-DIP µC module
+8V to +20V at 0.25A
+5V at 0.2A
-5V at 0.2A
888-522-5372
847-803-6100
Installs the EV kit files on your computer
Application program
MAX1168 EV kit help file
Uninstalls the EV kit software
Software loaded into the 68HC16 µC
MAX1168 EV Kit Files
PHONE
Component Suppliers
Connection Option
FUNCTION
www.fairchildsemi.com
www.component.tdk.com
Quick Start
WEBSITE
Procedure
2) Verify that jumper JU1 is ON, disabling DSP mode.
3) Verify that jumper JU2 is connected to pins 2-3,
4) Carefully connect the boards by aligning the 40-pin
5) Ensure that the 68HC16MODULE-DIP module’s
6) Connect the +8V to +20V power supply to the µC
7) Connect the +5V power supply to the VDD pad
8) Connect the -5V power supply to the VEE pad (with
9) Connect the USBTO232 board to the 68HC16MOD-
10) The MAX1168 EV kit software should have already
11) Start the MAX1168 EV kit software by clicking on its
12) Turn on the +5V power supply, followed by the -5V
13) Press the OK button to automatically connect and
14) Apply an input signal (0 to +4.096V) between AIN0
• MAX1168 EV system
• Three DC power supplies:
Recommended Equipment —RS-232/COM
enabling an 8-bit-wide data-transfer mode.
connector of the MAX1168 EV kit with the 40-pin
header of the 68HC16MODULE-DIP module. Gently
press them together. The two boards should be
flush against one another.
SW1 switch is in the OFF position.
module’s terminal block (J2), located next to the
ON/OFF switch (SW1) along the top edge of the µC
module. Observe the polarity marked on the board.
(with respect to the GND pad) on the MAX1168 EV
kit board.
respect to the GND pad) on the MAX1168 EV kit
board.
ULE-DIP module if you have not done so already.
been downloaded and installed in the USBTO232
Quick Start.
icon in the Start | Programs menu.
power supply. Finally, turn on the +8V to +20V
power supply and move the 68HC16MODULE-DIP
module’s slide switch (SW1) to the ON position.
download the KIT1168.C16 file to the module.
and GND. Observe the AIN0 label on the running
Windows program.
MAX1168 EV kit
68HC16MODULE-DIP µC module
USBTO232
+8V to +20V at 0.25A
+5V at 0.2A
-5V at 0.2A
Port PC Connection Option