MOD-ZIGBEE-PIR Olimex Ltd., MOD-ZIGBEE-PIR Datasheet
MOD-ZIGBEE-PIR
Specifications of MOD-ZIGBEE-PIR
Related parts for MOD-ZIGBEE-PIR
MOD-ZIGBEE-PIR Summary of contents
Page 1
... MOD-ZIGBEE-PIR sensor development board USER’S MANUAL All boards produced by Olimex LTD are ROHS compliant Designed by OLIMEX Ltd, 2011 Revision B, Januray 2013 ...
Page 2
... This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product. Thank you for purchasing the MOD-ZIGBEE-PIR board manufactured by Olimex! MOD-ZIGBEE-PIR Olimex 2012 © ...
Page 3
... OVERVIEW…………………………………………………………………….………………4 SECTION 2 SETTING UP THE DEVELOPMENT BOARD SECTION 3 MOD-ZIGBEE-PIR BOARD DESCRIPTION SECTION 4 THE PIC18F26K20 SECTION 5 CONTROL CIRCUITRY… ...
Page 4
... The document’s organization is then detailed. 1.1 Scope The MOD-ZIGBEE-PIR is a motion detector unit equipped with passive infrared (PIR) sensor which utilizes open source ZigBee stack, and has the option to be configured to use MiWi stack. This guide focuses on MOD-ZIGBEE-PIR board. ...
Page 5
... FR-4 is the most used glass-reinforced epoxy laminate for PCBs. 1.4 Similar boards MOD-ZIGBEE-UEXT is a version of MOD-ZIGBEE-PIR without the motion detection sensor supplied by a single battery and has a female UEXT connector. MOD-ZIGBEE-UEXT is thinner than MOD-ZIGBEE-PIR because of the different battery types used for battery powering of the board ...
Page 6
... A grounding strap or similar protective device should be worn when handling the board. Avoid touching the component pins or any other metallic element. 2.2 Requirements In order to set up the MOD-ZIGBEE-PIR evaluation board, the following items are required: - The MOD-ZIG-BEE development board itself - ...
Page 7
... The ZigBee and Microchip’s MiWi can be downloaded for free. Note that you can use MiWi if you don’t use Microchip’s transceiver + Microchip’s processor. For general programming we recommend you use Microchip’s MPLAB IDE and compiler C18. MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 8
... Here you get acquainted with the main parts of the board. Note the names used on the board differ from the names used here to describe them. For the actual names check the MOD-ZIGBEE-PIR board itself. For example: BUTTON (seen on the op view below) is named BUT; RESET is named RST; etc 3 ...
Page 9
... Layout (Bottom view): MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 10
... Sleep mode: < 100 nA @ 1.8V • Watchdog Timer: < 800 nA @ 1.8V • Timer1 Oscillator: < 800 kHz and 1.8V Analog Features: • Analog-to-Digital Converter (ADC) module: - 10-bit resolution, 13 External Channels - Auto-acquisition capability - Conversion available during Sleep THE PIC18F26K20 MICROCONTROLLER Olimex 2012 © MOD-ZIGBEE-PIR SECTION 4 Page ...
Page 11
... RS-232 operation using internal oscillator - Auto-Wake-up on Break - Auto-Baud Detect For comprehensive information on the microcontroller visit the Microchip’s web page for a datasheet. At the moment of writing the microcontroller datasheet can be found at the following link: http://ww1.microchip.com/downloads/en/DeviceDoc/41303G.pdf MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 12
... Providing 3.3V via the UEXT When powered and functional the current consumption is ~30 mA. 5.2 Reset MOD-ZIGBEE-PIR reset circuit includes D1 (0.2W, SMD), R1 (10kΩ), R2 (330Ω), C21 (100nF), PIC18F26K20 pin 1 (MCLR#) and a RESET button. 5.3 Clock Quartz crystal Q1 20.000 MHz is connected to PIC18F26K20 pin 33 (OSC2) and pin 34 (OSC1). ...
Page 13
... UEXT MOD-ZIGBEE-PIR board has UEXT connector and can interface Olimex's UEXT modules. Note that the UEXT connector on MOD-ZIGBEE-PIR is a female one. The Tx and Rx by default are in DEVICE mode. To switch to HOST mode set the jumpers to position 1-3 (D). For more information on UEXT please visit: http://www ...
Page 14
... Not connected 6.3 Jumper description JP1 & JP2 These jumpers, when both in position 2-3, enable DEVICE UEXT. These jumpers, when both in position 1-2, enable HOST UEXT. Default state is 2-3. UEXT_SUPPLY When closed the board is powered by the UEXT. Default state is open. MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 15
... There are two test pads RA1 and RA2 near the PIC MCU. They are connected to pins 9 and 10 of the MCU, resepctively. 6.5 LEDs & Buttons The board has 2 LEDS: LED1 is RED; LED2 is GREEN. The board has 2 user buttons: B1 and B2. MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 16
... Memory map MOD-ZIGBEE-PIR SECTION 7 MEMORY Olimex 2012 © Page ...
Page 17
... Eagle schematic MOD-ZIGBEE-PIR schematic can also be downloaded at our web page for MOD-ZIGBEE-PIR: http://olimex.com/dev/mod-zigbee-pir.html. They are located in HARDWARE section. The EAGLE schematic is situated on the next page for quicker reference. MOD-ZIGBEE-PIR SECTION 8 SCHEMATICS Olimex 2012 © Page ...
Page 18
... MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 19
... Physical dimensions Here you can find the physical dimensions of the board in millimeters. 8.2.1 Top view 8.2.2 Bottom view MOD-ZIGBEE-PIR Olimex 2012 © Page ...
Page 20
... Revision A B Fixed several mistakes and added newer schematic ORDER CODES: MOD-ZIGBEE-PIR - assembled, programmed, tested, calibrated development boards PIC-ICD2-POCKET + PIC-ICSP - for custom programming/debugging (if you do not wish to use PINGUINO IDE) PIC-KIT3 + PIC-ICSP - for custom programming/debugging (if you do not wish to use PINGUINO IDE) How to order? You can order from our online shop directly or from any of our distributors ...