MAX5970EVKIT+ Maxim Integrated, MAX5970EVKIT+ Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
MAX5970EVKIT+
Manufacturer Part Number
MAX5970EVKIT+
Description
Power Management IC Development Tools MAX5970 Eval Kit
Manufacturer
Maxim Integrated
Series
MAX5970r
Datasheet
1.MAX5970EVKIT.pdf
(18 pages)
Specifications of MAX5970EVKIT+
Rohs
yes
MAX5970 Evaluation Kit
Table 1. Jumper Description (JU1–JU16)
4
JUMPER
______________________________________________________________________________________
JU10
JU11
JU12
JU1
JU2
JU3
JU4
JU5
JU6
JU7
JU8
JU9
SHUNT POSITION
Open
Open
Open
Open
Open
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
1-2*
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
—
—
Powers the MAX5970 using the VS1, VS2 or VIN input supply
Powers the MAX5970 using the USB or VIN input supply
Powers the MAX5970 using the VIN input supply
See Table 3 for SMBus/I²C address settings
See Table 3 for SMBus/I²C address settings
Connects the POL pin of the MAX5970 to DREG through a pullup resistor for
active-high PG_ outputs
Connects the POL pin of the MAX5970 to GND for active-low PG_ outputs
Connects the MODE pin of the MAX5970 to DREG through a pullup resistor for the
channels to operate as a group
Connects the MODE pin of the MAX5970 to GND for the channels to operate as an
individual hot-swap controller
The MODE pin of the MAX5970 is not connected and the channels operate as a group
Connects the PROT pin of the MAX5970 to DREG through a pullup resistor, allowing
ALERT output to be asserted and respective PG_ output deasserted upon critical UV/
OV fault
Connects the PROT pin of the MAX5970 to GND, allowing ALERT output to be
asserted, and shuts down respective channel upon critical UV/OV fault
The PROT pin of the MAX5970 is not connected and ALERT output asserted upon
critical UV/OV fault
Configures the LED1 pin of the MAX5970 to drive an LED
Configures the LED1 pin of the MAX5970 as a GPIO
Configures the LED2 pin of the MAX5970 to drive an LED
Configures the LED2 pin of the MAX5970 as a GPIO
Configures the LED3 pin of the MAX5970 to drive an LED
Configures the LED3 pin of the MAX5970 as a GPIO
Configures the LED4 pin of the MAX5970 to drive an LED
Configures the LED4 pin of the MAX5970 as a GPIO
Connects the IRNG2 pin of the MAX5970 to DREG, which sets the channel 2 DAC
current-sense range to 50mV**
Connects the IRNG2 pin of the MAX5970 to GND, which sets the channel 2 DAC
current-sense range to 25mV**
The IRNG2 pin of the MAX5970 is not connected, which sets the channel 2 DAC
current-sense range to 100mV**
Connects the IRNG1 pin of the MAX5970 to DREG, which sets the channel 1 DAC
current-sense range to 50mV**
Connects the IRNG1 pin of the MAX5970 to GND, which sets the channel 1 DAC
current-sense range to 25mV**
The IRNG1 pin of the MAX5970 is not connected, which sets the channel 1 DAC
current-sense range to 100mV**
DESCRIPTION