MAX17501FTEEVKIT# Maxim Integrated, MAX17501FTEEVKIT# Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
MAX17501FTEEVKIT#
Manufacturer Part Number
MAX17501FTEEVKIT#
Description
Power Management IC Development Tools MAX17501E/F Eval Kit
Manufacturer
Maxim Integrated
Type
DC/DC Converters, Regulators & Controllersr
Series
MAX17501r
Datasheet
1.MAX17501FTEVKIT.pdf
(10 pages)
Specifications of MAX17501FTEEVKIT#
Rohs
yes
Product
Evaluation Kits
Tool Is For Evaluation Of
MAX17501E, MAX17501F
Input Voltage
6 V to 60 V
Output Voltage
5 V
Output Current
500 mA
For Use With
MAX17501E, MAX17501F
*EP = Exposed pad.
Note: Indicate that you are using the MAX17501 when contacting these component suppliers.
• MAX17501B or MAX17501F EV kit
• 6V to 60V, 1A DC input power supply
• Load capable of sinking 500mA
• Digital voltmeter (DVM)
• Function generator
The EV kit is fully assembled and tested. Follow the
steps below to verify the board operation. Caution: Do
not turn on power supply until all connections are
completed.
1) Set the power supply at a voltage between 6V and
2) Connect the positive terminal of the power supply
3) Connect the DVM across the VOUT PCB pad and the
Maxim Integrated
Coilcraft, Inc.
Murata Electronics North America, Inc.
Panasonic Corp.
60V. Disable the power supply.
to the VIN PCB pad and the negative terminal to the
nearest PGND PCB pad. Connect the positive termi-
nal of the 500mA load to the VOUT PCB pad and the
negative terminal to the nearest PGND PCB pad.
nearest PGND PCB pad.
MAX17501BTEVKIT#
MAX17501FTEVKIT#
EV KIT
SUPPLIER
Recommended Equipment
MAX17501B/ MAX17501F Evaluation Kits
Evaluate: MAX17501B/MAX17501F
Quick Start
DESIGNATION
Procedure
U1
U1
—
—
847-639-6400
770-436-1300
800-344-2112
PHONE
4) Verify that a shunt is installed across pins 1-2 on
5) Turn on the DC power supply.
6) Enable the load.
7) Verify that the DVM displays the expected voltage.
To turn-on/off the part from EN/UVLO, follow the steps
below:
1) Remove resistors R1 and R2 and the jumper installed
2) Connect the power supply to the EV kit and turn on
3) Connect the function generator output to the
4) EN/UVLO rising threshold is 1.24V and falling thresh-
5) While powering down the EV kits, first disconnect the
Buck converter (10 TDFN-EP*)
Maxim MAX17501BATB+
PCB: MAX17501BT EVALUATION KIT
Buck converter (10 TDFN-EP*)
Maxim MAX17501FATB+
PCB: MAX17501FT EVALUATION KIT
jumper JU1.
across pins 1-2 on jumper JU1.
the power supply. Set the power supply at a voltage
between 6V and 60V.
EN/UVLO test loop.
old is 1.11V. Make sure that the voltage-high and
voltage-low levels of the function generator output are
greater than 1.24V and less than 1.11V, respectively.
function generator output from the EN/UVLO test loop
and then turn off the DC power supply.
EV Kit-Specific Component List
www.coilcraft.com
www.murata-northamerica.com
www.panasonic.com
in TDFN Packages
DESCRIPTION
Component Suppliers
WEBSITE
2