ICTE-10RL4 ON Semiconductor, ICTE-10RL4 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
ICTE-10RL4
Manufacturer Part Number
ICTE-10RL4
Description
TVS Diodes - Transient Voltage Suppressors 10V 1500W
Manufacturer
ON Semiconductor
Series
1N6373-1N6381r
Datasheet
1.ICTE-015.pdf
(6 pages)
Specifications of ICTE-10RL4
Product Category
TVS Diodes - Transient Voltage Suppressors
Polarity
Unidirectional
Operating Voltage
10 V
Breakdown Voltage
11.7 V
Clamping Voltage
8 V
Peak Surge Current
10 A
Package / Case
DO-201AD
Minimum Operating Temperature
- 65 C
Maximum Operating Temperature
+ 175 C
Channels
1 Channel
Dimensions
5.3 (Max) mm W x 9.5 (Max) mm L
Peak Pulse Power Dissipation
1500 W
Termination Style
Axial
RESPONSE TIME
placed in parallel with the equipment or component to be
protected. In this situation, there is a time delay associated
with the capacitance of the device and an overshoot
condition associated with the inductance of the device and
the inductance of the connection method. The capacitance
effect is of minor importance in the parallel protection
scheme because it only produces a time delay in the
transition from the operating voltage to the clamp voltage as
shown in Figure 8.
turn‐on time (time required for the device to go from zero
current to full current) and lead inductance. This inductive
effect produces an overshoot in the voltage across the
equipment or component being protected as shown in
Figure 9. Minimizing this overshoot is very important in the
application, since the main purpose for adding a transient
suppressor is to clamp voltage spikes. These devices have
excellent response time, typically in the picosecond range
and negligible inductance. However, external inductive
effects could produce unacceptable overshoot. Proper
1000
In most applications, the transient suppressor device is
The inductive effects in the device are due to actual
500
200
100
50
20
10
5
2
1
0.3
DV
T
t
P
BR
L
= 10 ms
= 25°C
, INSTANTANEOUS INCREASE IN V
0.5 0.7
Figure 6. Dynamic Impedance
1
2
1N6373 - 1N6381 Series (ICTE-5 - ICTE-36)
3
V
BR
BR(MIN)
5
ABOVE V
19 V
7
21.2 V
= 6.0 to 11.7 V
10
BR(NOM)
APPLICATION NOTES
http://onsemi.com
42.4 V
(VOLTS)
20 30
4
0.07
0.05
0.03
0.02
0.01
circuit layout, minimum lead lengths and placing the
suppressor device as close as possible to the equipment or
components to be protected will minimize this overshoot.
prevent overstress of the protection device. This impedance
should be as high as possible, without restricting the circuit
operation.
DUTY CYCLE DERATING
and at a lead temperature of 25°C. If the duty cycle increases,
the peak power must be reduced as indicated by the curves
of Figure 7. Average power must be derated as the lead or
ambient temperature rises above 25°C. The average power
derating curve normally given on data sheets may be
normalized and used for this purpose.
in error as the 10 ms pulse has a higher derating factor than
the 10 ms pulse. However, when the derating factor for a
given pulse of Figure 7 is multiplied by the peak power value
of Figure 1 for the same pulse, the results follow the
expected trend.
0.7
0.5
0.3
0.2
0.1
1
Some input impedance represented by Z
The data of Figure 1 applies for non‐repetitive conditions
At first glance the derating curves of Figure 7 appear to be
0.1
Figure 7. Typical Derating Factor for Duty Cycle
0.2
0.5
1
D, DUTY CYCLE (%)
2
5
10 ms
10
in
PULSE WIDTH
20
is essential to
100 ms
1 ms
10 ms
50
100