M27C4002-10C1 STMicroelectronics, M27C4002-10C1 Datasheet - Page 9
![IC OTP 4MBIT 100NS 44PLCC](/photos/7/28/72894/m27c4002-10c1_sml.jpg)
M27C4002-10C1
Manufacturer Part Number
M27C4002-10C1
Description
IC OTP 4MBIT 100NS 44PLCC
Manufacturer
STMicroelectronics
Datasheet
1.M27C4002-10C1.pdf
(24 pages)
Specifications of M27C4002-10C1
Format - Memory
EPROMs
Memory Type
OTP EPROM
Memory Size
4M (256K x 16)
Speed
100ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
44-PLCC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-5674-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M27C4002-10C1
Manufacturer:
ST
Quantity:
34 000
Company:
Part Number:
M27C4002-10C1
Manufacturer:
ST
Quantity:
5 510
Company:
Part Number:
M27C4002-10C1
Manufacturer:
STMicroelectronics
Quantity:
10 000
M27C4002
2.4
2.5
2.6
System considerations
The power switching characteristics of Advanced CMOS EPROMs require careful
decoupling of the devices. The supply current, I
the system designer: the standby current level, the active current level, and transient current
peaks that are produced by the falling and rising edges of E. The magnitude of the transient
current peaks is dependent on the output capacitive and inductive loading of the device. The
associated transient voltage peaks can be suppressed by complying with the two line output
control and by properly selected decoupling capacitors. It is recommended that a 0.1µF
ceramic capacitor be used on every device between V
frequency capacitor of low inherent inductance and should be placed as close to the device
as possible. In addition, a 4.7µF bulk electrolytic capacitor should be used between V
V
connection point.The purpose of the bulk capacitor is to overcome the voltage drop caused
by the inductive effects of PCB traces.
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27C4002 are in the
'1' state. Data is introduced by selectively programming '0's into the desired bit locations.
Although only '0's will be programmed, both '1's and '0's can be present in the data word.
The only way to change a '0' to a '1' is by die exposure to ultraviolet light (UV EPROM). The
M27C4002 is in the programming mode when V
pulsed to V
pins. The levels required for the address and data inputs are TTL. V
6.25V ± 0.25V.
PRESTO II programming algorithm
PRESTO II Programming Algorithm allows the whole array to be programmed with a
guaranteed margin, in a typical time of 26.5 seconds. Programming with PRESTO II
consists of applying a sequence of 100µs program pulses to each byte until a correct verify
occurs (see
automatically activated in order to guarantee that each cell is programmed with enough
margin. No overprogram pulse is applied since the verify in MARGIN MODE provides
necessary margin to each programmed cell.
SS
for every eight devices. The bulk capacitor should be located near the power supply
IL
Figure
. The data to be programmed is applied to 16 bits in parallel to the data output
5). During programming and verify operation, a MARGIN MODE circuit is
CC
PP
, has three segments that are of interest to
input is at 12.75V, G is at V
CC
and V
SS
. This should be a high
CC
is specified to be
Device operation
IH
and E is
CC
and
9/24