CAT24C256YI-G ON Semiconductor, CAT24C256YI-G Datasheet - Page 8

• Manufacturer Part Number: CAT24C256YI-G
• Description: IC EEPROM 256KBIT 400KHZ 8TSSOP
• Manufacturer: ON Semiconductor

Specifications of CAT24C256YI-G

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 256K (32K x 8)
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-TSSOP
• Organization: 32 K x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.4 MHz
• Access Time: 900 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Maximum Operating Current: 1 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 3.3 V, 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

READ OPERATIONS
Immediate Address Read
counter points to the data byte immediately following the
last byte accessed by a previous operation. If that ‘previous’
byte was the last byte in memory, then the address counter
will point to the 1st memory byte, etc.
with a Slave address containing a ‘1’ in the R/W bit position
(Figure 10), it will acknowledge (ACK) in the 9th clock cycle,
and will then transmit data being pointed at by the internal
address counter. The Master can stop further transmission by
issuing a NoACK, followed by a STOP condition.
Selective Read
different from the one stored in the internal address counter.
In standby mode, the CAT24C256 internal address
When, following a START, the CAT24C256 is presented
The Read operation can also be started at an address
BUS ACTIVITY:
BUS ACTIVITY:
* = Don’t Care Bit
SDA LINE
SDA LINE
MASTER
MASTER
SCL
SDA
S
S
T
A
R
T
ADDRESS
SLAVE
ADDRESS
SLAVE
BUS ACTIVITY:
A
C
K
SDA LINE
MASTER
Figure 10. Immediate Address Read Timing
DATA n
A
C
K
DATA OUT
*
8th Bit
Figure 12. Sequential Read Timing
Figure 11. Selective Read Timing
8
A
15
S
S
T
A
R
T
− A
BYTE ADDRESS
C
A
K
8
http://onsemi.com
ADDRESS
SLAVE
DATA n+1
A
C
K
8
A
7
9
A
C
K
The address counter can be initialized by performing a
‘dummy’ Write operation (Figure 11). Here the START is
followed by the Slave address (with the R/W bit set to ‘0’)
and the desired two byte address. Instead of following up
with data, the Master then issues a 2nd START, followed by
the ‘Immediate Address Read’ sequence, as described
earlier.
Sequential Read
by the CAT24C256, then the device will continue
transmitting as long as each data byte is acknowledged by
the Master (Figure 12). If the end of memory is reached
during sequential Read, then the address counter will
‘wrap−around’ to the beginning of memory, etc. Sequential
Read works with either ‘Immediate Address Read’ or
‘Selective Read’, the only difference being the starting byte
address.
− A
NO ACK
A
C
K
If the Master acknowledges the 1st data byte transmitted
0
DATA
DATA n+2
A
C
K
S
S
T
A
R
T
ADDRESS
O
N
A
C
K
SLAVE
O
P
S
T
P
A
C
K
STOP
A
C
K
DATA n+x
DATA
O
N
A
C
K
O
S
T
P
P
O
N
A
C
K
O
S
T
P
P