37LV65-I/P Microchip Technology, 37LV65-I/P Datasheet
37LV65-I/P
Specifications of 37LV65-I/P
Related parts for 37LV65-I/P
37LV65-I/P Summary of contents
Page 1
... FPGAs. The 37LV36/65/128 family is available in the standard 8-pin plastic DIP, 8-pin SOIC and 20-pin PLCC packages. Device Bits Programming Word 37LV36 36,288 1134 x 32 37LV65 65,536 2048 x 32 37LV128 131,072 4096 x 32 Xilinx is a registered trademark of Xilinx Corporation. 2004 Microchip Technology Inc. Obsolete Device ...
Page 2
... Programming Voltage Supply 7 17 +3.0V to 6.0V Power Supply 8 20 Tamb = 0°C to +70°C Tamb = -40°C to +85°C Conditions OUT CC Tamb = MHz (Note 1) CLK V = 6.0V, CLK = 10 MHz 3.6V, CLK = 2.5 MHz CC Outputs open V = 6.0V 5. 3.6V 3.4V CC 2004 Microchip Technology Inc. ...
Page 3
... Programming Voltage Supply Used to enter programming mode (+13 volts) and to program the memory (+13 volts). Must be connected directly to Vcc for normal Read operation. No over- shoot above +14 volts is permitted. 2004 Microchip Technology Inc. 37LV36/65/128 8.0 CASCADING SERIAL EPROMS Cascading Serial EPROMs provide additional memory ...
Page 4
... MHz = V /2. LOAD CC 2004 Microchip Technology Inc. = 3.0V Conditions Notes 1, 2 Note 1 Note 1 ...
Page 5
... CLK to Data Float Delay CDF T CLK to CEO Delay OCK CEO Delay OCE T RESET/OE to CEO Delay OOE Note 1: This parameter is periodically sampled and not 100% tested. 2: Float delays are measured with output pulled through 2004 Microchip Technology Inc. 37LV36/65/128 AC Testing Waveform 0.2V Test Load _MAX Limits 3 ...
Page 6
... CE and OE HIGH and V clock edges and then lowering V ing clock edge. A word is programmed by strobing the device with V for the duration TPGM normal read operation power supply input for two rising for one more ris must be tied to V for PP CC 2004 Microchip Technology Inc. ...
Page 7
... Note 1: This parameter is periodically sampled and not 100% tested. Note 2: While in Programming Mode, CE should only be changed while OE is HIGH and has been HIGH for 200 ns, and OE should only be changed while CE is HIGH and has been HIGH for 200 ns. 2004 Microchip Technology Inc. Min. 1 ...
Page 8
... FIGURE 11-5: DETAILS OF PROGRAM CYCLE DS21109F-page 8 Exit Mode T SVC 500 s 500 s 500 s Programming Programming Mode Mode Mode **Load **Load Word 2 Word 3 data latches High if RESET/OE configured * * * Low if RESET/OE configured = 500 s Programming Mode **Load **Load Word 5 Word 4 Clock Increments Address Counter * 2004 Microchip Technology Inc. ...
Page 9
... FIGURE 11-6: READ MANUFACTURER AND DEVICE ID OVERVIEW FIGURE 11-7: DETAILS OF READ MANUFACTURER AND DEVICE ID 2004 Microchip Technology Inc. 37LV36/65/128 DS21109F-page 9 ...
Page 10
... Load 32-bit word to be programmed Pulse (13V) for Tpgm (500 s) No Last Word? Yes Exit Programming Mode Device Power Off Device Power On Verify Fail All Data Bits (Read Mode and CC PP CCL CCH Pass Device Passed IH Yes 2004 Microchip Technology Inc. ...
Page 11
... P = Plastic DIP, 8 lead SN = Plastic SOIC (150 mil Body), 8 lead L = Plastic Leaded Chip Carrier (PLCC), 20 lead Blank = 0°C to +70° -40°C to +85°C Blank = Tube T = Tape and Reel 37LV128 128K Serial EPROM 37LV65 64K Serial EPROM 37LV36 36K Serial EPROM DS21109F-page 11 ...
Page 12
... NOTES: DS21109F-page 12 2004 Microchip Technology Inc. ...
Page 13
... PICLAB, PICtail, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPICDEM, Select Mode, Smart Serial, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 14
... Via Salvatore Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands Waegenburghtplein 4 NL-5152 JR, Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/12/04 2004 Microchip Technology Inc. ...