AT29LV010A-15JC Atmel, AT29LV010A-15JC Datasheet
AT29LV010A-15JC
Specifications of AT29LV010A-15JC
Available stocks
Related parts for AT29LV010A-15JC
AT29LV010A-15JC Summary of contents
Page 1
... Commercial and Industrial Temperature Ranges 1. Description The AT29LV010A is a 3-volt only in-system Flash programmable and erasable read only memory (Flash). Its 1 megabit of memory is organized as 131,072 bytes by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 120 ns with power dissipation of just 54 mW over the commercial tem- perature range. When the device is deselected, the CMOS standby current is less than 40 µ ...
Page 2
... Pin Configurations Pin Name A0 - A16 I/O0 - I/O7 NC 2.1 32-lead PLCC Top View 2.2 32-lead TSOP Top View – Type 1 AT29LV010A 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect A14 A13 A11 A10 I/ I/O7 A11 A13 4 29 A14 5 28 ...
Page 3
... Device Operation 4.1 Read The AT29LV010A is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual-line con- trol gives designers flexibility in preventing bus contention ...
Page 4
... DATA Polling The AT29LV010A features DATA polling to indicate the end of a program cycle. During a pro- gram cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin ...
Page 5
... These two 8K memory sections are referred to as boot blocks. Secure code which will bring up a system can be contained in a boot block. The AT29LV010A blocks are located in the first 8K bytes of memory and the last 8K bytes of memory. The boot block programming lockout feature can therefore support systems that boot from the lower addresses of memory or the higher addresses ...
Page 6
... Device Code A16 =V Manufacturer Code A16 =V Device Code IH IL Min Max 1 1 Com. 40 Ind 0.6 2.0 0.45 2.4 AT29LV010A-25 0°C - 70°C -40°C - 85°C 3.3V ± 0.3V I/O D OUT D IN High Z High Z (4) (4) (4) (4) Units μA μA μA μ 0520F–FLASH–9/08 ...
Page 7
... AT29LV010A-12 AT29LV010A-15 Min Max Min 120 120 (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact AT29LV010A AT29LV010A-20 AT29LV010A-25 Max Min Max Min 150 200 150 200 70 0 100 ACC after an address change CE ACC ...
Page 8
... Input Test Waveforms and Measurement Level t R 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. These parameters are characterized and not 100% tested. AT29LV010A < Max 6 12 Units Conditions OUT 0520F–FLASH–9/08 ...
Page 9
... Chip Select Hold Time CH t Write Pulse Width ( Data Set-up Time Data, OE Hold Time DH OEH t Write Pulse Width High WPH 15. AC Byte Load Waveforms 15.1 WE Controlled 15.2 CE Controlled 0520F–FLASH–9/08 (1)(2) AT29LV010A Min Max Units 10 100 0 0 200 100 10 200 ...
Page 10
... LOAD DATA A0 TO ADDRESS 5555 WRITES ENABLED LOAD DATA TO ENTER DATA (3) SECTOR (128 BYTES) PROTECT STATE AT29LV010A 10 (1) Notes: 1. Data Format: I/O7 - I/O0 (Hex); Address Format: A14 - A0 (Hex). 2. Data Protect state will be re-activated at end of program cycle. 3. 128 bytes of data MUST BE loaded. (2) ...
Page 11
... Toggle Bit Waveforms Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 0520F–FLASH–9/08 (1) (1) (1)(3) AT29LV010A Min Typ Max Min Typ ...
Page 12
... IL Manufacturer Code is read for Device Code is read for The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code is 1F. The Device Code is 35. AT29LV010A 12 25. Boot Block Lockout Feature Enable Algorithm (2)(3)(5) Notes: (4) ; ...
Page 13
... Plastic J-Leaded Chip Carrier (PLCC) 32T 32-Lead, Thin Small Outline Package (TSOP) 0520F–FLASH–9/08 Ordering Code Package AT29LV010A-12JC 32J AT29LV010A-12TC 32T AT29LV010A-12JI 32J AT29LV010A-12TI 32T AT29LV010A-15JC 32J AT29LV010A-15TC 32T AT29LV010A-15JI 32J AT29LV010A-15TI 32T AT29LV010A-20JC 32J AT29LV010A-20TC 32T AT29LV010A-20JI 32J ...
Page 14
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29LV010A 14 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 15
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0520F–FLASH–9/08 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT29LV010A 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 16
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...