AT45DB321B-CI Atmel, AT45DB321B-CI Datasheet - Page 6

• Manufacturer Part Number: AT45DB321B-CI
• Description: IC FLASH 32MBIT 20MHZ 44CBGA
• Manufacturer: Atmel

Specifications of AT45DB321B-CI

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 32M (8192 pages x 528 bytes)
• Speed: 20MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-CBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Block Erase Addressing
6
PA12
0
0
0
0
1
1
1
1
•
•
•
AT45DB321B
PA11
0
0
0
0
1
1
1
1
•
•
•
PA10
0
0
0
0
1
1
1
1
•
•
•
PA9
0
0
0
0
1
1
1
1
•
•
•
BUFFER TO MAIN MEMORY PAGE PROGRAM WITHOUT BUILT-IN ERASE: A
previously erased page within main memory can be programmed with the contents of
either buffer 1 or buffer 2. To start the operation, an 8-bit opcode, 88H for buffer 1 or
89H for buffer 2, must be followed by the one reserved bit, 13 address bits (PA12 - PA0)
that specify the page in the main memory to be written, and ten additional don’t care
bits. When a low-to-high transition occurs on the CS pin, the part will program the data
stored in the buffer into the specified page in the main memory. It is necessary that the
page in main memory that is being programmed has been previously erased. The pro-
gramming of the page is internally self-timed and should take place in a maximum time
of t
Successive page programming operations without doing a page erase are not recom-
mended. In other words, changing bytes within a page from a “1” to a “0” during multiple
page programming operations without erasing that page is not recommended.
PAGE ERASE: The optional Page Erase command can be used to individually erase
any page in the main memory array allowing the Buffer to Main Memory Page Program
without Built-in Erase command to be utilized at a later time. To perform a Page Erase,
an opcode of 81H must be loaded into the device, followed by one reserved bit,
13 address bits (PA12 - PA0), and ten don’t care bits. The 13 address bits are used to
specify which page of the memory array is to be erased. When a low-to-high transition
occurs on the CS pin, the part will erase the selected page to 1s. The erase operation is
internally self-timed and should take place in a maximum time of t
the status register will indicate that the part is busy.
BLOCK ERASE: A block of eight pages can be erased at one time allowing the Buffer
to Main Memory Page Program without Built-in Erase command to be utilized to reduce
programming times when writing large amounts of data to the device. To perform a
Block Erase, an opcode of 50H must be loaded into the device, followed by one
reserved bit, ten address bits (PA12 - PA3), and 13 don’t care bits. The ten address bits
are used to specify which block of eight pages is to be erased. When a low-to-high tran-
sition occurs on the CS pin, the part will erase the selected block of eight pages to 1s.
The erase operation is internally self-timed and should take place in a maximum time of
t
BE
. During this time, the status register will indicate that the part is busy.
P
. During this time, the status register will indicate that the part is busy.
PA8
0
0
0
0
1
1
1
1
•
•
•
PA7
0
0
0
0
1
1
1
1
•
•
•
PA6
0
0
0
0
1
1
1
1
•
•
•
PA5
0
0
0
0
1
1
1
1
•
•
•
PA4
0
0
1
1
0
0
1
1
•
•
•
PA3
0
1
0
1
0
1
0
1
•
•
•
PA2
X
X
X
X
X
X
X
X
•
•
•
PA1
X
X
X
X
X
X
X
X
•
•
•
PE
. During this time,
2223E–DFLASH–11//03
PA0
X
X
X
X
X
X
X
X
•
•
•
Block
1020
1021
1022
1023
0
1
2
3
•
•
•