AT49BV4096A-12RC Atmel, AT49BV4096A-12RC Datasheet

no-image

AT49BV4096A-12RC

Manufacturer Part Number
AT49BV4096A-12RC
Description
IC FLASH 4MBIT 120NS 44SOIC
Manufacturer
Atmel
Datasheet

Specifications of AT49BV4096A-12RC

Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8 or 256K x 16)
Speed
120ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
44-SOIC
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
2Features
Description
The AT49BV004(T) and AT49BV4096A(T) are 3-volt, 4-megabit Flash Memories
organized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufac-
tured with Atmel’s advanced nonvolatile CMOS technology, the devices offer access
times to 120 ns with power dissipation of just 67 mW at 2.7V read. When deselected,
the CMOS standby current is less than 50 µA.
The device contains a user-enabled “boot block” protection feature. Two versions of
the feature are available: the AT49BV004/4096A locates the boot block at lowest
order addresses (“bottom boot”); the AT49BV004T/4096AT locates it at highest order
addresses (“top boot”).
To allow for simple in-system reprogrammability, the AT49BV004(T)/4096A(T) does
not require high input voltages for programming. Reading data out of the device is
similar to reading from an EPROM; it has standard CE, OE, and WE inputs to avoid
bus contention. Reprogramming the AT49BV004(T)/4096A(T) is performed by first
erasing a block of data and then programming on a byte-by-byte or word-by-word
basis.
Pin Configurations
Pin Name
A0 - A18
CE
OE
WE
RESET
RDY/BUSY
VPP
I/O0 - I/O14
I/O15(A-1)
BYTE
NC
2.7V to 3.6V Read/Write Operation
Fast Read Access Time - 120 ns
Internal Erase/Program Control
Sector Architecture
Fast Sector Erase Time - 10 seconds
Byte-by-Byte or Word-By-Word Programming - 30 µs Typical
Hardware Data Protection
DATA Polling For End Of Program Detection
Low-Power Dissipation
Typical 10,000 Write Cycles
– One 8K Words (16K bytes) Boot Block with Programming Lockout
– Two 4K Words (8K bytes) Parameter Blocks
– One 240K Words (480K bytes) Main Memory Array Block
– 25 mA Active Current
– 50 µA CMOS Standby Current
Function
Addresses
Chip Enable
Output Enable
Write Enable
Reset
Ready/Busy Output
Optional Power Supply for Faster
Program/Erase Operations
Data Inputs/Outputs
I/O15 (Data Input/Output, Word Mode)
A-1 (LSB Address Input, Byte Mode)
Selects Byte or Word Mode
No Connect
(continued)
4-Megabit
(512K x 8/
256K x 16)
Flash Memory
AT49BV004
AT49BV004T
AT49BV4096A
AT49BV4096AT
Preliminary
Rev. 1139A–09/98
1

Related parts for AT49BV4096A-12RC

AT49BV4096A-12RC Summary of contents

Page 1

... Typical 10,000 Write Cycles Description The AT49BV004(T) and AT49BV4096A(T) are 3-volt, 4-megabit Flash Memories organized as 524,288 words of 8 bits each or 256K words of 16 bits each. Manufac- tured with Atmel’s advanced nonvolatile CMOS technology, the devices offer access times to 120 ns with power dissipation of just 2.7V read. When deselected, the CMOS standby current is less than 50 µ ...

Page 2

... For the AT49BV4096A(T), the BYTE pin controls whether the device data I/O pins operate in the byte or word config- uration. If the BYTE pin is set at a logic “1” or left open, the device is in word configuration, I/O0 - I/O15 are active and controlled by CE and OE. ...

Page 3

... AT49BV004(T) Block Diagram VCC VPP GND RESET ADDRESS INPUTS AT49BV4096A(T) Block Diagram GND RESET ADDRESS INPUTS Device Operation READ: The AT49BV004(T)/4096A(T) is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high ...

Page 4

... A T49 BV004 and AT49BV4096A; 7C002 for the AT49BV004T; and 3E002H for the AT49BV4096AT. If the data on I/O0 is low, the boot block can be programmed; if the data on I/O0 is high, the program lockout feature has been enabled and the block cannot be programmed ...

Page 5

For details, see Operating Modes (for hardware operation) or Software Product Identification. The manufacturer and device code is the same for both modes. DATA POLLING: The AT49BV004(T)/4096A(T) features DATA polling to indicate the end of a program cycle. During a ...

Page 6

... The ADDRESS FORMAT in each bus cycle is as follows: A15 - A0 (Hex), A-1, and A15 - A18 (Don’t Care) 2. The boot sector has the address range 00000H to 03FFFH for the AT49BV004; 7C000H to 7FFFFH for the AT49BV004T; 00000H to 01FFFH for the AT49BV4096A; and 3E000H to 3FFFFH for the AT49BV4096AT. 3. Either one of the Product ID Exit commands can be used. ...

Page 7

... Notes can Refer to AC Programming Waveforms 12.0V 0.5V Manufacturer Code: 161FH Device Code: 11H (AT49BV004), 1692H (AT49BV4096A), 10H (AT49BV004T), 1690H (AT49BV4096AT). 5. See details under Software Product Identification Entry/Exit pin is optional. Please contact Atmel Characteristics Symbol Parameter I Input Load Current LI I Output Leakage Current ...

Page 8

AC Read Characteristics Symbol Parameter t Address to Output Delay ACC ( Output Delay CE ( Output Delay OE (3)( Output Float DF t Output Hold from OE,CE or ...

Page 9

AC Word Load Characteristics Symbol Parameter Address, OE Set-up Time AS OES t Address Hold Time AH t Chip Select Set-up Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...

Page 10

Program Cycle Characteristics Symbol Parameter t Byte/Word Programming Time BP t Address Set-up Time AS t Address Hold Time AH t Data Set-up Time DS t Data Hold Time DH t Write Pulse Width WP t Write Pulse Width High ...

Page 11

Data Polling Characteristics Symbol Parameter t Data Hold Time Hold Time OEH ( Output Delay OE t Write Recovery Time WR Notes: 1. These parameters are characterized and not 100% tested. 2. See t ...

Page 12

... The device does not remain in identification mode if pow- ered down. 4. The device returns to standard operation mode. 5. Manufacturer Code: 161FH Device Code: 11H (AT49BV004), 1692H (AT49BV4096A), 1692H (AT49BV004T), 1690H (AT49BV4096AT) 6. Either one of the Product ID Exit commands can be used. AT49BV004/4096A(T) 12 (1) Boot Block ...

Page 13

AT49BV004(T) Ordering Information I (mA ACC Standby (ns) Active 120 25 0.05 120 25 0.05 40T 40-Lead, Plastic Thin Small Outline Package (TSOP) Ordering Code AT49BV004-12TC AT49BV004-12TI AT49BV004T-12TC AT49BV004T-12TI Package Type Package Operation Range 40T Commercial (0 to ...

Page 14

... Wide, Plastic Gull Wing Small Outline (SOIC) 48T 48-Lead, Plastic Thin Small Outline Package (TSOP) AT49BV004/4096A(T) 14 Ordering Code Package AT49BV4096A-12RC 44R AT49BV4096A-12TC 48T AT49BV4096A-12RI 44R AT49BV4096A-12TI 48T AT49BV4096AT-12RC 44R AT49BV4096AT-12TC 48T AT49BV4096AT-12RI 44R AT49BV4096AT-12TI ...

Page 15

Packaging Information 44R, 44-Lead, 0.525" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) 48T, 48-Lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches)* JEDEC OUTLINE MO-142 D *Controlling dimension: millimeters 40T, 40-Lead, Plastic ...

Page 16

... No licenses to patents or other intellectual prop Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...

Related keywords