AT24C01A-10SC-2.5 Atmel, AT24C01A-10SC-2.5 Datasheet - Page 22
![IC EEPROM 1KBIT 400KHZ 8SOIC](/photos/6/50/65032/453-8-soic_sml.jpg)
AT24C01A-10SC-2.5
Manufacturer Part Number
AT24C01A-10SC-2.5
Description
IC EEPROM 1KBIT 400KHZ 8SOIC
Manufacturer
Atmel
Datasheet
1.AT24C01A-10PC.pdf
(24 pages)
Specifications of AT24C01A-10SC-2.5
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
1K (128 x 8)
Speed
100kHz, 400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
0°C ~ 70°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
AT24C01A10SC2.5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT24C01A-10SC-2.5
Manufacturer:
AT
Quantity:
20 000
5TS1 – SOT23
22
NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing
AT24C01A/02/04/08/16
R
2. Dimension D does not include mold flash, protrusions, or gate burrs.
3. The package top may be smaller than the package bottom. Dimensions
4. These dimensions apply to the flat section of the lead between 0.08 mm
5. Dimension "b" does not include Dambar protrusion. Allowable Dambar
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
MO-193, Variation AB, for additional information.
Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per end.
Dimension E1 does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.15 mm per side.
D and E1 are determined at the outermost extremes of the plastic body
exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but
including any mismatch between the top and bottom of the plastic body.
and 0.15 mm from the lead tip.
protrusion shall be 0.08 mm total in excess of the "b" dimension at
maximum material condition. The Dambar cannot be located on the lower
radius of the foot. Minimum space between protrusion and an adjacent lead
shall not be less than 0.07 mm.
Seating
Plane
E1
1
5
Top View
b
Side View
TITLE
5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink
Small Outline Package (SHRINK SOT)
e1
D
2
e
3
4
A2
E
A1
A
SYMBOL
A
A1
A2
c
D
E
E1
L1
e
e1
b
0.00
0.70
0.08
0.30
COMMON DIMENSIONS
MIN
(Unit of Measure = mm)
–
C
End View
2.90 BSC
2.80 BSC
1.60 BSC
0.60 REF
0.95 BSC
1.90 BSC
NOM
0.90
–
–
–
–
DRAWING NO.
PO5TS1
C
L
L1
1.10
0.10
1.00
0.20
MAX
0.50
0180T–SEEPR–12/04
NOTE
4, 5
2, 3
2, 3
2, 3
4
6/25/03
REV.
A