AT27C040-90TC Atmel, AT27C040-90TC Datasheet
AT27C040-90TC
Specifications of AT27C040-90TC
Related parts for AT27C040-90TC
AT27C040-90TC Summary of contents
Page 1
... The AT27C040 chip is a low-power, high-performance, 4,194,304-bit one-time pro- grammable read-only memory (OTP EPROM) organized as 512K by 8 bits. The AT27C040 requires only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 70 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems. Atmel’ ...
Page 2
... GND 16 17 2.2 32-lead TSOP Top View A11 A13 4 A14 5 A17 6 A18 7 VCC 8 VPP 9 A16 10 A15 11 A12 AT27C040 2 Function Addresses Outputs Chip Enable Output Enable 2.3 32-lead PLCC Top View VCC A18 A17 A14 A13 A8 A9 A11 OE A10 A10 GND 23 02 ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. AT27C040 3 ...
Page 4
... The supply current would then be the sum ( ( Identification Code except A9 which is set to V and A0 which is toggled select the Device Code byte. IH AT27C040-90 -40°C - 85°C 5V ± 10% Min Max ±1 ±5 10 100 -0.6 0.8 2 0.5 CC 0.4 2 Outputs D OUT High Z High Z ...
Page 5
... This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 0189H–EPROM–12/07 Condition ( after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C040 AT27C040 -70 -90 Min Max Min Max ACC ...
Page 6
... Input Test Waveforms and Measurement Levels 12. Output Test Load 13. Pin Capacitance ( MHz 25° C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C040 6 1.3V (1N914) 3.3K OUTPUT PIN CL Max Units Conditions OUT ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C040 a 0.1 µF capacitor is required across V transients. 0189H–EPROM–12/07 (1) and 2.0V for AT27C040 and ground to suppress spurious voltage ...
Page 8
... This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 100 µsec ± 5%. 17. Atmel’s AT27C040 Integrated Product Identification Code Codes A0 Manufacturer 0 ...
Page 9
... V are read again and compared with the original data to determine if the device passes or fails. 0189H–EPROM–12/07 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5.0V and V PP AT27C040 5.0V. All bytes CC 9 ...
Page 10
... Plastic Thin Small Outline Package (TSOP) AT27C040 10 Standby Ordering Code AT27C040-70JI 0.1 AT27C040-70PI AT27C040-70TI AT27C040-90JI 0.1 AT27C040-90PI AT27C040-90TI Standby Ordering Code AT27C040-70JU 0.1 AT27C040-70PU AT27C040-70TU AT27C040-90JU 0.1 AT27C040-90PU AT27C040-90TU Package Type Package Operation Range 32J Industrial 32P6 (-40° 85° C) 32T 32J Industrial 32P6 (-40° 85° C) 32T ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0189H–EPROM–12/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C040 0.318(0.0125) 0.191(0.0075 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 3.175 – ...
Page 12
... PDIP A SEATING PLANE Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R AT27C040 12 D PIN 0º ~ 15º REF eB TITLE 32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual ...
Page 13
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0189H–EPROM–12/07 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT27C040 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...