AT27C516-70VI Atmel, AT27C516-70VI Datasheet
AT27C516-70VI
Specifications of AT27C516-70VI
Related parts for AT27C516-70VI
AT27C516-70VI Summary of contents
Page 1
... PLCC and VSOP packages. The device features two-line control (CE, OE) to eliminate bus contention in high-speed systems. With 32K word storage capability, the AT27C516 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. ...
Page 2
... A0 - A14 O0 - O15 CE OE PGM NC Note: 2.1 40-lead VSOP (Type 1) Top View 2.2 44-lead PLCC Top View Note: PLCC Package Pins 1 and 23 are Don’t Connect. AT27C516 2 Function Addresses Outputs Chip Enable Output Enable Program Strobe No Connect Both GND pins must be connected ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability (1) AT27C516 3 ...
Page 4
... ( ( A14 = except A9 which is set to V and A0 which is toggled select the Device Code byte. IH will cause a slight increase AT27C516 -40°C - 85°C 5V ± 10% Min Max ± 1 ± 0.3V 100 + 0. -0.6 0.8 2 0.5 CC 0.4 2 Outputs D OUT High Z High OUT High Z Identification Code -70 Units µ ...
Page 5
... Output float is defined as the point when data is no longer driven. 0362E–EPROM–1/08 (1) Condition 0.8V and after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C516 AT27C516 -45 -70 Min Max Min Max 0.0V and V = 3.0V. Timing mea ...
Page 6
... For -45, and -70 devices only: 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C516 < (10 Note 100 pF including jig L capacitance, except -45 and -70 devices, where pF. ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C516 at 0.1 µF capacitor is required across V voltage transients. 0362E–EPROM–1/08 (1) and 2.0V for AT27C516 and ground to suppress spurious ...
Page 8
... This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 50 µsec ± 5%. 17. Atmel’s AT27C516 Integrated Product Identification Code Codes A0 Manufacturer 0 ...
Page 9
... V are read again and compared with the original data to determine if the device passes or fails. 0362E–EPROM–1/08 is raised to 13.0V. Each address is first programmed with one 50 µ then lowered to 5.0V and V PP AT27C516 5.0V. All words CC 9 ...
Page 10
... Plastic J-leaded Chip Carrier (PLCC) 40V 40-lead, Plastic Thin Small Outline Package (VSOP) AT27C516 10 Ordering Code Package AT27C516-45JI 44J AT27C516-45VI 40V AT27C516-70JI 44J AT27C516-70VI 40V Ordering Code Package AT27C516-45JU 44J AT27C516-70JU Package Type Operation Range (2) Industrial (-40° 85° C) (2) Operation Range Industrial (-40° ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0362E–EPROM–1/08 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C516 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 4.191 – ...
Page 12
... E Notes: 1. This package conforms to JEDEC reference MO-142, Variation CA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27C516 12 PIN SEATING PLANE A1 TITLE ...
Page 13
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...