AT24C02A-10TU-2.7 Atmel, AT24C02A-10TU-2.7 Datasheet
AT24C02A-10TU-2.7
Specifications of AT24C02A-10TU-2.7
Related parts for AT24C02A-10TU-2.7
AT24C02A-10TU-2.7 Summary of contents
Page 1
... Die Sales: Wafer Form, Waffle Pack, and Bumped Wafers. Description The AT24C02A/04A provides 2048/4096 bits of serial electrically erasable and program- mable read-only memory (EEPROM) organized as 256/512 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low- power and low-voltage operation are essential ...
Page 2
... DEVICE/PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that must be hardwired for the AT24C02A. As many as eight 2K devices may be addressed on a single bus system. (Device addressing is discussed in detail under Device Addressing, page 8). ...
Page 3
... Upper Half (1K) Array CC At GND AT24C02A, 2K SERIAL EEPROM: The 2K is internally organized with 32 pages of 8 bytes each. Random word addressing requires an 8-bit data word address. AT24C04A, 4K SERIAL EEPROM: The 4K is internally organized with 32 pages of 16 bytes each. Random word addressing requires a 9-bit data word address. ...
Page 4
... IH V Output Low Level V = 3.0V OL2 CC V Output Low Level V = 1.8V OL1 CC Note min and V max are reference only and are not tested AT24C02A/04A 4 = −40°C to +85° Test Condition Min 1.8 2.5 2.7 4.5 READ at 100 kHz WRITE at 100 kHz ...
Page 5
... Max 100 4.7 4.0 (2) 100 0.1 4.5 4.7 (1) 4.0 4.7 0 200 1.0 300 4.7 100 5 1M AT24C02A/04A = +1.8V to +5.5V TTL Gate and 100 CC 2.5, 2.7, 5.0-volt Min Max Units 400 kHz 1.2 0.6 50 0.1 0.9 1.2 0.6 0.6 0 100 0.3 300 ...
Page 6
... The EEPROM sends a “0” to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C02A/04A/08A/16A features a low-power standby mode that is enabled: (a) upon power-up and (b) after the receipt of the Stop bit and the com- pletion of any internal operations. ...
Page 7
... Figure 5. Write Cycle Timing SCL SDA 8th BIT WORDn Notes: 1. The write cycle time t is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. WR Figure 6. Output Acknowledge 0976Q–SEEPR–8/05 ACK t wr STOP CONDITION AT24C02A/04A (1) START CONDITION 7 ...
Page 8
... Device Addressing Write Operations AT24C02A/04A 8 The 2K and 4K EEPROM devices require an 8-bit device address word following a start condition to enable the chip for a read or write operation, as shown in Figure 7. Figure 7. Device Address 2K 1 MSB 4K 1 The device address word consists of a mandatory “1”, “0” sequence for the first four most significant bits as shown ...
Page 9
... EEPROM inputs are disabled, acknowledge polling can be initiated. This involves send- ing a start condition followed by the device address word. The read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a “0” allowing the read or write sequence to continue. AT24C02A/04A DATA ( DATA ( ...
Page 10
... Read Operations AT24C02A/04A 10 Read operations are initiated the same way as write operations with the exception that the read/write select bit in the device address word is set to “1”. There are three read operations: current address read, random address read and sequential read. ...
Page 11
... Figure 12. Sequential Read 0976Q–SEEPR–8/05 tial read will continue. The sequential read operation is terminated when the microcontroller does not respond with a “0” but does generate a following stop condition, see Figure 12. AT24C02A/04A 11 ...
Page 12
... AT24C02AN-10SI-2.7 AT24C02A-10TI-2.7 AT24C02A-10PI-1.8 AT24C02AN-10SI-1.8 AT24C02A-10TI-1.8 (2) AT24C02A-10PU-2.7 (2) AT24C02A-10PU-1.8 (2) AT24C02AN-10SU-2.7 (2) AT24C02AN-10SU-1.8 (2) AT24C02A-10TU-2.7 (2) AT24C02A-10TU-1.8 (2) AT24C02AY1-10YU-1.8 (2) AT24C02AU3-10UU-1.8 (3) AT24C02A-W2.7-11 (3) AT24C02A-W1.8-11 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. 2. “U” designates Green Package + RoHS compliant 3. Available in waffle pack and wafer form; order as SL719 for wafer form. Bumped die available upon request. Please contact Serial EEPROM Marketing ...
Page 13
... Die Sale Die Sale Package Type Options AT24C02A/04A Operation Range Industrial Temperature (−40°C to 85°C) Industrial Temperature (−40°C to 85°C) Lead-free/Halogen-free/ Industrial Temperature (−40°C to 85°C) Industrial Temperature (−40°C to 85°C) ...
Page 14
... D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT24C02A/04A ...
Page 15
... These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0976Q–SEEPR–8/ Top View TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT24C02A/04A ∅ End View COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 1.35 – 1. ...
Page 16
... Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. 2325 Orchard Parkway San Jose, CA 95131 R AT24C02A/04A TITLE 8A2, 8-lead, 4 ...
Page 17
... This drawing is for general information only. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 0976Q–SEEPR–8/ TITLE 8U3-1, 8-ball, 1.50 x 2.00 mm Body, 0.50 mm pitch, Small Die Ball Grid Array Package (dBGA2) AT24C02A/04A Side View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX SYMBOL NOM A 0 ...
Page 18
... MAP D E Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R AT24C02A/04A End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP PIN 1 INDEX AREA Bottom View COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX NOTE – ...
Page 19
... Orchard Parkway San Jose, CA 95131 R 0976Q–SEEPR–8/ Side View TITLE 8Y5, 8-lead 2.0 x 3.0 mm Body, 0.50 mm Pitch, Mini-Map, Dual No Lead Package (DFN) AT24C02A/04A b D2 (8x) Pin (8x) e (6x) 1.50 REF. Bottom View COMMON DIMENSIONS (Unit of Measure = mm) MIN MAX ...
Page 20
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...