AT24C64A-10TI-2.7 SL383 Atmel, AT24C64A-10TI-2.7 SL383 Datasheet
AT24C64A-10TI-2.7 SL383
Specifications of AT24C64A-10TI-2.7 SL383
Related parts for AT24C64A-10TI-2.7 SL383
AT24C64A-10TI-2.7 SL383 Summary of contents
Page 1
... PDIP 8-lead TSSOP VCC SCL GND 4 GND 4 5 SDA Two-wire Serial EEPROM 32K (4096 x 8) 64K (8192 x 8) AT24C32A AT24C64A Notes: 1. Not recommended for new refer to AT24C32C. 2. Not recommended for new refer to AT24C64C GND 8 VCC SCL 5 SDA (1) (2) design; please design ...
Page 2
Absolute Maximum Ratings* Operating Temperature..................................–55°C to +125°C Storage Temperature .....................................–65°C to +150°C Voltage on Any Pin with Respect to Ground .................................... –1.0V to +7.0V Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Figure 1. Block Diagram AT24C32A/64A 2 ...
Page 3
... Device Addressing section). If the pins are left floating, the A2, A1 and A0 pins will be internally pulled down to GND if the capacitive coupling to the circuit board V <3 pF. If coupling is >3 pF, Atmel recommends connecting the address pins to GND. WRITE PROTECT (WP): The write protect input, when connected to GND, allows nor- mal write operations ...
Page 4
Table 2. Pin Capacitance Applicable over recommended operating range from T Symbol Test Condition C Input/Output Capacitance (SDA) I/O C Input Capacitance ( Note: 1. This parameter is characterized and is not 100% tested. Table ...
Page 5
Table 4. AC Characteristics Applicable over recommended operating range from T 100 pF (unless otherwise noted) Symbol f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High HIGH t Noise Suppression Time I t ...
Page 6
... MEMORY RESET: After an interruption in protocol, power loss or system reset, any two-wire part can be reset by following these steps: (a) Clock cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high. 3054T– ...
Page 7
Figure 2. Bus Timing SCL: Serial Clock, SDA: Serial Data I/O Figure 3. Write Cycle Timing SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The write cycle time t is the time from a ...
Page 8
Figure 5. Start and Stop Definition Figure 6. Output Acknowledge AT24C32A/64A 8 3054T–SEEPR–1/07 ...
Page 9
... DATA SECURITY: The AT24C32A/64A has a hardware data protection scheme that allows the user to write protect the entire memory when the WP pin BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and acknowledgment ...
Page 10
... The address “roll over” during read is from the last byte of the last memory page, to the first byte of the first page. The address “roll over” during write is from the last byte of the cur- rent page to the first byte of the same page ...
Page 11
Figure 7. Device Address Figure 8. Byte Write Figure 9. Page Write Notes DON’T CARE bits 2. † = DON’T CARE bits for the 32K Figure 10. Current Address Read 3054T–SEEPR–1/07 11 ...
Page 12
Figure 11. Random Read Note DON’T CARE bits Figure 12. Sequential Read AT24C32A/64A 12 3054T–SEEPR–1/07 ...
Page 13
AT24C32A Ordering Information Ordering Code (2) AT24C32A-10PU-2.7 (2) AT24C32A-10PU-1.8 (2) AT24C32AN-10SU-2.7 (2) AT24C32AN-10SU-1.8 (2) AT24C32AW-10SU-2.7 (2) AT24C32AW-10SU-1.8 (2) AT24C32A-10TU-2.7 (2) AT24C32A-10TU-1.8 (2) AT24C32AY1-10YU-1.8 (Not recommended for new design) (3) AT24C32AY6-10YH-1.8 (4) AT24C32A-W1.8-11 Notes: 1. For 2.7V devices used in the ...
Page 14
... AT24C64A Ordering Information Ordering Code (2) AT24C64A-10PU-2.7 (2) AT24C64A-10PU-1.8 (2) AT24C64AN-10SU-2.7 (2) AT24C64AN-10SU-1.8 (2) AT24C64AW-10SU-2.7 (2) AT24C64AW-10SU-1.8 (2) AT24C64A-10TU-2.7 (2) AT24C64A-10TU-1.8 (2) AT24C64AY1-10YU-1.8 (Not recommended for new design) (3) AT24C64AY6-10YH-1.8 (4) AT24C64A-W1.8-11 Notes: 1. For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC Characteristics tables. 2. “U” designates Green Package + RoHS compliant. ...
Page 15
Package Drawings 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions A and L are measured ...
Page 16
JEDEC SOIC Top View e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R ...
Page 17
EIAJ SOIC 1 N Top View e D Side View Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs ...
Page 18
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, ...
Page 19
MAP D E Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R 3054T–SEEPR–1/ End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm ...
Page 20
MAP D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is measured between 0.15 mm and 0.30 mm ...
Page 21
Revision History 3054T–SEEPR–1/07 Doc. Rev. Date Comments 3054T 1/2007 Implemented revision history. Added Notes to Page 1 recommending new devices. 21 ...
Page 22
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...